Avaya IP Office Phone Manager Installation Manual Download Page 351

Page: 351 / 411

IP Office Installation

Page 350

15-601042 Issue 20b (16 July 2009)

IP Office

10.12 Physical Ports

The following port types are found on IP Office systems:

Port

Found on

Description

ANALOG

ATM4 Trunk card (x4).
Analog Trunk expansion module
(x16).

Used for the connection of external analog trunks.

AUDIO

All IP Office control units (x1).

Used for input of an external music on hold source.

BRI

Quad BRI trunk card (x4).
So8 expansion module (x8).

Used for connection of BRI trunks (Quad BRI trunk card) and
ISDN terminals devices (So8 module).

DC I/P

All control units (x1).
All expansion modules (x1).

Power input from external power supply unit.

IP403 control unit (x8).
IP406 V2 control unit (x8).
Digital Station expansion modules
(x16/x30).

Connection of Avaya digital station

phones supported by IP Office

RS232/DTE

All control units (x1).
All expansion modules (x1).

Used for control unit maintenance under Avaya guidance. On
expansion modules not used.

EXPANSION

All control units (x various).
All expansion modules except
WAN3 (x1).

Used for interconnection of external expansions modules and
control units.

EXT O/P

All control units (x1).

Used to control external relay systems. The port provides two
switchable (on, off and pulse) controls.

All modules (x1).

Used for connection of functional or protective ground if required.

LAN

All control units (x various).

10/100Mbps Ethernet LAN ports.

Analog Trunk expansion module
(x2).

Analog power fails ports.

PHONE
(POT)

IP403 control unit (x2).
IP406 V2 control unit (x2).
Phones expansion modules (x8/
x16/x30).

Analog phone extension ports. On older units these ports are
labeled as POT ports.

PRI

Single PRI trunk cards (x1).

Dual PRI trunk cards (x2).

PRI trunk ports.

USB

IP500 Control Unit (x1).

Not used.

WAN

All control units (x1).

WAN3 expansion module (x3).

WAN interface ports. V.24, V.35 and X.21 through cable selection.

Small Office Edition (x1)

RJ45 Ethernet port. Acts as Layer 3 ethernet switch to the
modules LAN ports.

Summary of Contents for IP Office Phone Manager




























































































































































































































































































































































































































Search results

Summary of Contents for IP Office Phone Manager

Reviews:

Avaya IP Office Phone Manager, Installation Manual, Page: 351 / 411

Search results

Summary of Contents for IP Office Phone Manager

Reviews: