manualshive.com logo in svg

Avaya IP Office Phone Manager, Installation Manual, Page: 85 / 411

Share
Download
Avaya IP Office Phone Manager Installation Manual Download Page 85

IP Office Installation

Page 84

15-601042 Issue 20b (16 July 2009)

IP Office

5.6 Applying Power

This procedure starts a new IP Office control unit not connected to any LAN. In
this scenario the IP Office control unit will assume its default configuration
settings.  

 

Objective -

 To power up the IP Office control unit to a known state with a

known set of defaults.

 

Warnings

1. When powering up the control unit for the first time do not connect the LAN or

WAN ports of the control unit to any network.

2. The power cord must be connected directly from the control unit to the switched

power outlet socket. The cord must not be fixed in anyway or routed through
any permanent structure.

  

 

Parts and Equipment Required

•

o

 Switched power outlet socket.

•

o

 IP Office Control Unit.

•

o

 Locale Specific Power Cord.

 

Procedure

1. Connect the power cord from the power supply outlet to the power input socket on the rear of the control unit.

•

Power cords must not be attached to the building surface or run through walls, ceilings, floors and similar
openings. Installation measures must be taken to prevent physical damage to the power supply cord,
including proper routing of the power supply cord and provision of a socket outlet near the fixed equipment or
positioning of the equipment near a socket outlet.

2. Switch on power to the control unit.

3. New IP Office 500 control units are supplied with a base software level of 4.0.0. The CPU LED on these units will

flash red until the unit is upgraded to the required level of released IP Office core software.

4. The CPU LED on units that have already been upgraded from 4.0.0 will go through a green red cycle several times

and then stay green on. During this time other LED's may flash as the unit goes through its power on self test
cycle.

IP Office Default Settings

 

The following are the basic default configuration settings for an IP Office system.

System

Name

MAC address of the control unit.

System Password

password

License Server IP Address

255.255.255.255

LAN*

 

LAN1

LAN2/WAN

IP address

192.168.42.1.

192.168.43.1

IP Mask

255.255.255.0

255.255.255.0

DHCP Mode

Server

Server

No of DHCP IP Addresses

200.

200.

*See 

Default DHCP/Data Settings

 detail below. 

•

Extensions and Users

 

A user is automatically created for each physical extension port detected in the system. Users are assigned
extension numbers starting from 201. User names take the form Extn201, Extn202, ....

•

Hunt Group

 

A single hunt group 200 called Main is created and the first 10 users are placed into that hunt group as members.

•

Incoming Call Routes 

Two default incoming call routes are created. Voice calls are routed to the hunt group Main. Data calls are routed
to the RAS user DialIn.

Summary of Contents for IP Office Phone Manager




























































































































































































































































































































































































































Reviews:

No comments