Avaya IP Office Phone Manager Installation Manual Download Page 20

Page: 20 / 411

IP Office Installation

Page 19

15-601042 Issue 20b (16 July 2009)

IP Office

System Overview: Control Units

2.4 Control Unit Summary

The following table summarizes the capacities of the IP Office control units supported by IP Office 5.0 software.

Feature

IP400

IP500

IP406 V2

IP412

IP500

Plus 4-Port Exp

Card

Integral Digital Station (

) Ports

Up to 24

Integral Analog Phone (

PHONE

) Ports

Up to 32

Up to 24

Optional Embedded Voicemail Card Slot

Integral WAN Port

External Expansion Ports

DTE Port

9-way

Audio In (MOH) Port

External O/P Switch Port

Conference Parties

[1]

128

[4]

128

[4]

Configuration Memory

256KB

1024KB

Voicemail Pro/TAPI WAV Channels

[2]

Maximum Extension Capacity

190

360

384

[3]

384

[3]

- Digital (

) Phones only.

188

360

264

384

- Analog Phones only.

182

360

272

384

- IP Phones only.

190

360

384

[3]

384

IP400 Trunk Cards Supported

- Analog trunk cards

- Quad BRI trunk cards

- Single PRI trunk cards

- Dual PRI trunks cards

(Slot A)

- WAN port card

IP500 Trunk Daughter Cards

- IP500 Analog trunks

- IP500 BRI trunk channels

- IP500 PRI trunk channels

240

180

VCM Cards

- IP400 VCM Cards

- IP500 VCM Cards

Maximum voice compression channels

128

Dimensions

Height x Width x Depth

71x445x245mm

2.8"x17.5"x9.7"

73x445x365mm

2.9"x17.5"x14.4"

Notes

1. Where IP Office Conferencing Center is installed, 5 conference slots are reserved by the control unit for its own use

(call recording, etc) and are not available to IP Office Conferencing Center or for general conference usage.

2. IP500 Voicemail/TAPI WAV channels increased from 30 to 40 for IP Office 5.0+.

3. IP500 Maximum extensions increased from 272 to 384 for IP Office 5.0+.

4. IP500 Conference capacity increased from 64 to 128 for IP Office 5.0+.

5. For IP Office 5.0+, the IP500 no longer runs in separate Standard or Professional modes. No

IP500 Upgrade

Standard to Professional

license is required.

Summary of Contents for IP Office Phone Manager




























































































































































































































































































































































































































Search results

Summary of Contents for IP Office Phone Manager

Reviews:

Avaya IP Office Phone Manager, Installation Manual, Page: 20 / 411

Search results

Summary of Contents for IP Office Phone Manager

Reviews: