manualshive.com logo in svg

Avaya IP Office Phone Manager, Installation Manual, Page: 25 / 411

Share
Download
Avaya IP Office Phone Manager Installation Manual Download Page 25

IP Office Installation

Page 24

15-601042 Issue 20b (16 July 2009)

IP Office

 The following IP400 trunk card types are supported by IP Office 4.0:  

IP400 Trunk Cards

SOE

IP406
V2

IP412 IP500

Analog Trunk Card (ATM4)

 

Provides 4 RJ45 loop-start analog trunk ports.
The card is available in several locale specific
variants. This card has been superseded by the
ATM4U card below.

Additional loop or ground start analog trunks can
also be added using 

Analog Trunk

 external

expansion modules.

Analog Trunk Card (ATM4U)

 

Provides 4 RJ45 loop-start analog trunk ports as
per the ATM4 above but available in a single
worldwide variant. Also supports adjustable echo
cancellation on IP Office 3.1.

Additional loop or ground start analog trunks can
also be added using 

Analog Trunk

 external

expansion modules.

Quad BRI Trunk Card

 

Provides support for 4 RJ45 BRI (2B+D) trunk
ports. These can be configured to ETSI or
AusTS013 operation. The ports include 100ohm
termination.

Single PRI T1 Trunk Cards

 

Supports PRI (23B+D) trunks and T1 Robbed-Bit
(24B) trunks through a single RJ45 port. The
mode of operation is selected in the IP Office
configuration.

Single E1 PRI Trunk Cards

 

Supports PRI (30B+D) trunks through a single
RJ45 port. The port can be configured for PRI or
QSIG operation.

Single E1R2 Trunk Cards

 

Supports PRI (30B+D) trunks using E1R2
signalling. Available in coaxial or RJ45 connector
variants. Coaxial variants are not supported on
an IP500 carrier card.   

Dual PRI Trunk Cards

 

As the single PRI cards above but supporting the
connection of two PRI trunks. On the IP406 V2,
supported in Slot A only.

WAN Port Card

 

Used only with the Small Office Edition. Provides
a single 37-way D-type socket for connection to
a V.24, V.35 or X.21 WAN service. Includes a
replacement back panel for the control unit.

 

Summary of Contents for IP Office Phone Manager




























































































































































































































































































































































































































Reviews:

No comments