Avaya IP Office Phone Manager Installation Manual Download Page 196

Page: 196 / 411

IP Office Installation

Page 195

15-601042 Issue 20b (16 July 2009)

IP Office

Additional Processes: DTE Port Maintenance

Procedure: Erasing the Core Software via the Boot Loader

1. Run Manager. In the BOOTP entries, check that there is an entry that matches the MAC Address, IP Address and .bin

file used by the system (the first two details can be found in the Module settings in the system's configuration file).

2. If an entry is not present, create a new entry. Then close and restart Manager.

3. Under File | Preferences ensure that Manager is set to 255.255.255.255. Also check that Enable BootP Server is

checked.

4. Select View | TFTPLog.

5. Check that the required .bin file is present in Manager's working directory.

6. Attach the serial cable between the PC and the DTE port on the IP Office control unit.

7. Start the terminal program on your PC. Ensure that it has been setup as listed in

DTE Port Settings

. Within a

HyperTerminal session, the current settings are summarized across the base of the screen.

8. Arrange the program windows so that the Terminal program and Manager TFTP Log are visible at the same time.

9. Switch off power to the IP Office control unit.

10.Power on the control unit and press the escape key every second until you get a Loader message. Below is an

example.

P12 Loader 2.4
CPU Revision 0x0900

11.Enter AT (note upper case). The control unit should respond OK.

12.Enter AT-X. The control unit should respond Multi-Sector Erase.

13.The control unit will now request the .bin file it requires from Manager. This process appears in the TFTPLog.

14.If the file transfers does not appear to be taking place, check that the IP address shown in the TFTPLog matches the

BOOTP entry. Adjust the BOOTP entry if necessary.

15.When completed the system will reboot.

Summary of Contents for IP Office Phone Manager




























































































































































































































































































































































































































Search results

Summary of Contents for IP Office Phone Manager

Reviews:

Avaya IP Office Phone Manager, Installation Manual, Page: 196 / 411

Search results

Summary of Contents for IP Office Phone Manager

Reviews: