manualshive.com logo in svg

Avaya IP Office Phone Manager, Installation Manual, Page: 82 / 411

Share
Download
Avaya IP Office Phone Manager Installation Manual Download Page 82

IP Office Installation

Page 81

15-601042 Issue 20b (16 July 2009)

IP Office

IP500 Basic Installation: IP500 Card Installation

2. IP400 Legacy Card Installation

An IP500 Legacy Carrier card can be used to fit IP400 trunk or VCM cards into an IP500 control unit. Up to 2 IP500
carrier cards can be inserted.  

 PRI T1
 Dual PRI T1
 PRI 30 E1 (1.4)
 Dual PRI E1
 PRI 30 E1R2 RJ45
 Dual PRI E1R2 RJ45

 BRI-8 (UNI)
 ANLG 4 Uni (US only)
 VCM 4
 VCM 8
 VCM 16
 VCM 24
 VCM 30

 

 

 

Objective

 - To fit a IP400 card to an IP500 Legacy Card

Carrier.

 

Warnings

 

1. Correct anti-static protection steps should be taken before

handling circuit boards.

2. During this process power to the IP Office control unit must

be switched off and disconnected.

 

Parts and Equipment Required

1.

o

 IP500 Carrier Card.

2.

o

 IP400 Card 

The table opposite lists supported cards. Any card not listed
is not supported. Cards are supplied with 2 plastic stand off
pillars. Trunk cards are also supplied with a replacement
blanking plate which are not required with the IP500.

 

Tools Required

 

1.

o

 5mm Flat-blade screwdriver.

2.

o

 Anti-static wrist strap and ground point.

 

Procedure: Installing a Carrier Card

1. Check that correct cards have been supplied.

2. Ensure that you are wearing an anti-static wrist strap

connected to a suitable ground point.

3. On the carrier card identify the position of the jumper block

and stand off pillar holes for the IP400 card. The peg holes
are labeled as VCM or TRUNK.

4. If fitting an IP400 trunk card, identify which of the plastic

snap-off panels on the front of the carrier card need to be
removed to allow the trunk cable connections. Carefully
remove those panels.

5. Fit the stand off pillars to the IP500 carrier card.

6. Using minimal force and checking that the pins are correctly

located, push the IP400 card onto its jumper and the stand
off pillars.

 

Summary of Contents for IP Office Phone Manager




























































































































































































































































































































































































































Reviews:

No comments