manualshive.com logo in svg

Avaya IP Office Phone Manager, Installation Manual, Page: 81 / 411

Share
Download
Avaya IP Office Phone Manager Installation Manual Download Page 81

IP Office Installation

Page 80

15-601042 Issue 20b (16 July 2009)

IP Office

1. IP500 Trunk Daughter Card Installation

IP500 trunk daughter cards can be fitted to any IP500 base card except the IP500 Legacy Card Carrier.

 

 

Objective

 - To fit a IP500 trunk card to an IP500 base card.

 

Warnings

1. Correct anti-static protection steps should be taken before handling

circuit boards.

2. During this process power to the IP Office control unit must be

switched off and disconnected.

 

Parts and Equipment Required

1.

o

 Any IP500 base card except the IP500 Legacy Card Carrier base

card.

2.

o

 IP500 Trunk Card

3.

o

 5 Stand Off Pillars 

These are supplied with the trunk daughter card.

· With the release of the IP500 PRI-U trunk daughter card, the

design of stand off pillars supplied with all types of trunk daughter
card has changed. The original 5 plastic pillars have been replaced
by 2 metal pillars and 3 plastic pillars. The metals pillars are pre-
fitted to the trunk daughter cards in their intended position and two
screws and washers are supplied for final attachment to the base
card.

 

Tools Required.

1.

o

 5mm Flat-blade screwdriver.

2.

o

 Anti-static wrist strap and ground point. 

 

Procedure: Installing an IP500 Trunk Daughter Card

1. Check that correct cards have been supplied.

2. Ensure that you are wearing an anti-static wrist strap connected to a

suitable ground point.

3. On the base card identify the position of 3 holes for the plastic pillars

for the IP500 card. These are along the same edge as the card
connector.

4. Fit the stand off pillars to the IP500 base card.

5. If there is a clip-on metal shield over the connector block on the base

card, remove it.

6. Using minimal force and checking that the pins are correctly located,

push the IP500 trunk card onto its connector block and the stand off
pillars.

7. Check that the card connector has snapped into position.

8. Using the washers and screws provided, secure the metal stand off

pillars to the base card.  

9. A set of labels are supplied with the trunk daughter card. Fit the

appropriate label to the front of the base card.

10.Prepare any other IP500 cards. Then proceed to Inserting an IP500

Card

 

Summary of Contents for IP Office Phone Manager




























































































































































































































































































































































































































Reviews:

No comments