manualshive.com logo in svg

Avaya IP Office Phone Manager, Installation Manual, Page: 215 / 411

Share
Download
Avaya IP Office Phone Manager Installation Manual Download Page 215

IP Office Installation

Page 214

15-601042 Issue 20b (16 July 2009)

IP Office

10.2 IP500 Base Cards

The IP500 control unit has 4 slots for the insertion of base cards. Each
base cards includes an integral front panel with ports for cable
connections.

The slots are numbered 1 to 4 from left to right. Normally they can be
used in any order, however if the capacity for a particular type of card is
exceeded, the card in the highest slot will be disabled.

 

IP500 Digital Station Base Card

This card has 12 RJ45 ports. The first 8 ports are 

DS

 ports for the

connection of Avaya digital phones other than IP phones. The card can
be fitted with an IP500 daughter card which then uses the additional 4
RJ45 ports for connections.

•

This card accepts one IP500 daughter card of any type.

•

Maximum:

 3 per IP500 control unit.

•

4400 Series phones (4406D, 4412D and 4424D) are not supported
on this card. They are supported on an external expansion module. 

IP500 Analog Phone Base Card

This card has 12 RJ45 ports. The card is available in two variants,
providing 2 or 8 analog extension ports for the connection of analog
phones. The card can be fitted with an IP500 daughter card which then
uses the additional 4 RJ45 ports for connections.  

•

This card accepts one IP500 daughter card of any type.

•

Maximum:

 4 per IP500 control unit.

•

When fitted with an IP500 Analog Trunk daughter card, the Phone 8
base card supports 1 power failure extension to trunk (loop-start
only) connection.

•

The analog extension ports do not include a ringing capacitor. Where
this is a requirement, connection should be via a Master socket
containing ringing capacitors.

IP500 VCM Base Card

This card provides voice compression channels for use with VoIP calls.
The module is available in variants supporting up to 32 or 64 channels.
Each card provides 4 initial channels with additional channels being
enabled by licenses in the IP Office configuration. The card can be
fitted with an IP500 daughter card which then uses the 4 RJ45 ports for
connections.

The maximum number of voice compression channels supported, using
IP500 VCM cards and or IP400 VCM cards on IP500 carrier cards is
128.

•

This accepts one IP500 daughter card of any type.

•

Maximum:

 2 per IP500 control unit.

Summary of Contents for IP Office Phone Manager




























































































































































































































































































































































































































Reviews:

No comments