manualshive.com logo in svg

Avaya IP Office Phone Manager, Installation Manual, Page: 179 / 411

Share
Download
Avaya IP Office Phone Manager Installation Manual Download Page 179

IP Office Installation

Page 178

15-601042 Issue 20b (16 July 2009)

IP Office

9.6.2 Installation Requirements

Software

•

The IP Office Administration CD contains the Feature Key Server software. This is required for use with USB and
parallel port licence keys.

 

Feature Key

•

Ensure that the serial number on the Feature Key dongle is noted and recorded in a safe location. The number is
printed on the Feature Key dongle and prefixed with SN.

 

Feature Key Server PC

 

Only required if using a Parallel Port or USB Feature Key. Not applicable if using a Serial Port Feature Key dongle.

•

Windows 2003 or XP are strongly recommended as the Feature Key Server is then able to install as a service,
giving greater reliability.

•

The server PC should be located in a secure area. The Feature Key device is fundamental to the correct operation
of many features, so a record of its location and serial number must be kept.

•

Parallel Port Feature Key:

•

A 25-pin Parallel port 1, set to bidirectional operation in the PC's BIOS.

•

Bidirectional parallel port operation is the normal default on most PCs.

•

WARNING: Do not connect a printer to the parallel port Feature Key dongle. Poorly wired printer cables or
printers that have not been earthed correctly can cause the parallel port Feature Key to stop working.

•

USB Feature Key:

•

USB 1.1 or 2.0. Type A connector.

•

IP Office 1.4 Admin suite or later.

 

Network

•

The PC should be configured and tested for TCP/IP networking.

•

It should be on the same network segment as the IP Office. That is data traffic between the IP Office and the
Feature Key Server PC should not require routing.

•

The PC should have a fixed IP address. Whilst PC's in a DHCP network usually retain the same IP address between
reboots this is not guaranteed.

•

If the IP Office is acting as a DHCP server, then in default it uses addresses 192.168.42.2 to 192.168.42.201 for
DHCP clients. This leaves addresses between 192.168.42.202 and 192.168.42.254 free for devices that require
fixed IP addresses.

Summary of Contents for IP Office Phone Manager




























































































































































































































































































































































































































Reviews:

No comments