manualshive.com logo in svg

Avaya IP Office Phone Manager, Installation Manual, Page: 83 / 411

Share
Download
Avaya IP Office Phone Manager Installation Manual Download Page 83

IP Office Installation

Page 82

15-601042 Issue 20b (16 July 2009)

IP Office

D3. IP500 Card Installation

Having prepared each IP500 card by adding any IP400 cards or IP500 trunk daughter cards required, the base cards can
be inserted into the control unit.

 

Objective -

 To fit a IP500 base card into the IP500 control unit.

 

Warnings

•

Correct anti-static protection steps should be taken before handling circuit boards.

•

During this process power to the IP Office control unit must be switched off and disconnected.

 

Tools Required.

•

o

 5mm Flat-blade screwdriver.

•

o

 Anti-static wrist strap and ground point.

 

Procedure: Installing a Carrier Card

1. Switch off power to the IP500 control unit.

2. Using a flat-bladed screwdriver, remove the cover from the slot on the front of the control unit that will be used for

each card being installed. This cover is no longer required but should be retained until installation has been
completed.

3. Allowing the card to rest against the bottom of the slot, begin sliding it into the control unit. When half inserted,

check that the card rails have engaged with the slot edges by trying to gently rotate it. I the card does rotate
remove it and begin inserting it again.   

4. The card should slide in freely until almost fully inserted. At this point apply pressure at the base of the front of the

card to complete insertion.

5. Using a flat-bladed screwdriver secure the carrier card.

6. Reapply power to the control unit. Initially each card should show a red LED (two if a daughter card is fitted) as

the control unit restarts. After approximately 30 seconds these should change to flashing red as the card is
started. These should then change to flashing every 5 seconds if the cards have started correctly.

7. Run the IP Office System Status Application and verify that the cards have all been recognized.

8. IP Office Manager can now be used to configure the extensions and trunk lines. For any IP500 VCM base cards,

VCM Channel licenses must be added to the configuration to enable channels above the base 4.  

 

Summary of Contents for IP Office Phone Manager




























































































































































































































































































































































































































Reviews:

No comments