manualshive.com logo in svg

Avaya IP Office Phone Manager, Installation Manual, Page: 38 / 411

Share
Download
Avaya IP Office Phone Manager Installation Manual Download Page 38

IP Office Installation

Page 37

15-601042 Issue 20b (16 July 2009)

IP Office

System Overview: Cabling and Cables

Standard IP Office Cables

The following are Avaya standard cables available for use with IP Office systems. The maximum length is applicable if the
standard Avaya cable is replaced with an alternate cable.

Cable

Description

SAP Code

Standard
Length

Maximum
Length

9-Way DTE Cable

Connects to control unit RS232 DTE
port. 9-Way D-type plug to 9-way D-
type socket.

–

2m/6'6''.

2m/6'6''.

Structured Cabling DS Line Cable

Connects from RJ45 sockets to RJ11
socketed DS and analog phones.

700047871

4m/13'2''.

See table
below.

BRI/PRI Trunk Cable

Connects BRI/PRI trunk ports to the
line providers network termination
point. RJ45 to RJ45. Red.

700213440

3m/9'10''.

–

Expansion Interconnect Cable

Connects the control unit to expansion
modules (except WAN3 modules). RJ45
to RJ45. Blue.

700213457

1m/3'3''.

1m/3'3''.

LAN Cable

Connects from IP Office LAN ports to IP
devices. RJ45 to RJ45. Grey.

700213481

3m/9'10''.

100m/328'.

LAN Interconnect Cable

Connects WAN3 module to the control
unit. Replace with a LAN crossover
cable for IP412 control units. Green.

700213465

1m/3'3''.

–

LAN Crossover Cable

Used for connection of IP devices to
LAN ports on the IP412 control unit.
Black

700213473

3m/9'10''.

100m/328'.

V.24 WAN Cable

37-Way D-type plug to 25-way D-type
plug.

700213416

3m/9'10''.

5m/16'5''

V.35 WAN Cable

37-Way D-type plug to 34-way MRAC
plug.

700213424

3m/9'10''.

5m/16'5''

X.21 WAN Cable

37-Way D-type plug to 15-way D-type
plug.

700213408

3m/9'10''.

5m/16'5''

 

The table below details the maximum total cable distances for DS and analog extensions using different cable types.

Telephone

Unshielded Twisted-Pair (UTP) - 50nf/Km

CW1308

AWG22 

(0.65mm)

AWG24

(0.5mm)

AWG26 

(0.4mm)

2400/5400 Series

1200m/3937'.

1000m/3280'.

670m/2200'.

400m/1310'.

4406D Phone

1000m/3280'.

1000m/3280'.

400m/1310'.

400m/1310'.

4412D Phone

1000m/3280'.

700m/2295'.

400m/1310'.

400m/1310'.

4424D

500m/1640'.  

500m/1640'.

400m/1310'.

400m/1310'.

6400 Series

1000m/3280'.

1000m/3280'.

400m/1310'.

400m/1310'.

T3 Series (Upn)

1000m/3280'.

1000m/3280'.

400m/1310'.

–

Analog Phones

1000m/3280'.

1000m/ 3280'.

400m/1640'.

800m/2620'.

 

Summary of Contents for IP Office Phone Manager




























































































































































































































































































































































































































Reviews:

No comments