Avaya IP Office Phone Manager Installation Manual Download Page 35 | Manualshive

Page: 35 / 411

Avaya IP Office Phone Manager Installation Manual Download Page 35

IP Office Installation

Page 34

15-601042 Issue 20b (16 July 2009)

IP Office

2.11 Power Supply Cords

Each control unit and expansion module requires a switched power outlet socket rated at 110-240V ac, 50-60Hz.
Connection from that power outlet socket requires an appropriate locale specific power cord which is not supplied with
the unit and must be ordered separately.

Power cords must not be attached to the building surface or run through walls, ceilings, floors and similar openings.
Installation measures must be taken to prevent physical damage to the power supply cord, including proper routing of
the power supply cord and provision of a socket outlet near the fixed equipment or positioning of the equipment near a
socket outlet.

For locales not detailed below an appropriate power cord must be obtained locally.

Power Cord Type

Power Outlet Plug Type

Locales

SAP Codes

Earthed Power Cords (IEC60320 C13)

Control Units

•

IP500.

•

IP406 V2.

•

IP412.*

•

Small Office Edition.

IP400 External Expansion Modules

•

Digital Station V2.

•

Phone V2.

•

So8.*

•

WAN3 10/100.*

IP500 External Expansion Modules

•

BRI So8.

•

Digital Station 16/30.

•

Phone 16/30.

CEE7/7 (Schuko)

Europe and
South Africa.

700289762

BS1363

Czech Republic,
Ireland, United
Kingdom.

700289747

NEMA5-15P / CS22.2 No.42 North, Central

and South
America.

700289770

CPCS-CCC

China.

700261977

Unearthed Power Cord (IEC60320 C7)

IP400 External Expansion Modules

•

Analog.

•

Digital Station V1.

•

Phone V1.

IP500 External Expansion Modules

•

Analog Trunk 16.

CEE7/16 (Europlug)

Europe and
South Africa.

700213382

BS1363

Czech Republic,
Ireland, United
Kingdom.

700213374

NEMA1-15

North, Central
and South
America.

700213390

Korea.

700254519

China.

700314172

*Older units were supplied with a 40W unearthed PSU and required an IEC60320 C7 power cord.

«
...
33
34
35
36
37
...
»

Summary of Contents for IP Office Phone Manager




























































































































































































































































































































































































































Reviews:

No comments