manualshive.com logo in svg

Avaya IP Office Phone Manager, Installation Manual, Page: 119 / 411

Share
Download
Avaya IP Office Phone Manager Installation Manual Download Page 119

IP Office Installation

Page 118

15-601042 Issue 20b (16 July 2009)

IP Office

6.7 Fitting VCM Cards

VCM cards are used to provide voice compression channels for calls between IP and non-IP
devices, devices being both trunks and extensions. VCM cards with differing numbers of
voice compression channels are available.

 Objective - To fit the card and confirm its presence after restarting the IP Office.

 

Warnings

•

Correct anti-static protection steps should be taken before handling circuit boards.

•

During this process power to the IP Office control unit must be switched off and disconnected.

 

Parts and Equipment Required

•

o

 

VCM Card 

Check that the correct card has been supplied. The number and maximum capacity supported varies between
different IP Office control units. All cards are supplied with 2 plastic snap-in stand off pillars.

VCM Cards

SAP Code

IP406 V2

IP412

Voice Compression
Modules

(25ms echo
cancellation)

VCM5

700185119

VCM10

700185127

VCM20

700185135

VCM30

700293939

Voice Compression
Modules

(64ms echo
cancellation)

VCM4

700359854

VCM8

700359862

VCM16

700359870

VCM24

700359888

Number of VCM cards.

1

2

Maximum number of channels.

30

60

 

Tools Required.

•

o

 Cross-head screwdriver.

•

o

 Anti-static wrist strap and ground point.

•

o

 IP Office Monitor application.

Summary of Contents for IP Office Phone Manager




























































































































































































































































































































































































































Reviews:

No comments