manualshive.com logo in svg

Avaya IP Office Phone Manager, Installation Manual, Page: 242 / 411

Share
Download
Avaya IP Office Phone Manager Installation Manual Download Page 242

IP Office Installation

Page 241

15-601042 Issue 20b (16 July 2009)

IP Office

System Components: IP400 Internal Cards

10.6.3 Embedded Voicemail Memory Cards

These cards are supported on the Small Office Edition and the IP406 V2 control units. They are specially formatted
Compact Flash cards that provide embedded voicemail operation and can also be configured for basic auto-attendant
support.

Use of these cards for voicemail does not require a license.

•

 These cards are not hot swappable. Removal of the cards while the IP Office control unit is powered may cause

lose or corruption of messages and prompts.

Variant

Countr

y

SOE IP40

6

V2

IP41

2

IP50

0

SAP
Code

Small Office Edition

Uses a 64MB Compact Flash cards fitted into a PCMCIA
slot caddy. The card provides up to 10 hours storage
for compressed prompts, greetings and messages.
Operation of the card uses the one of the Small Office's
voice compression channels for each call.

All

7002897
21

IP406 V2

Uses a 512MB Compact Flash card. This card provides
up to 15 hours storage for uncompressed prompts,
greetings and messages. Operation of this card does
not require voice compression channels.

All

7003434
60

•

From IP Office 3.0 onwards, the prompt files for the following languages are pre-installed on the Avaya memory cards.
  

•

Danish

•

German

•

English-UK

•

English-US

•

Spanish

•

Spanish-Mexico

•

Spanish-Argentina

•

Finnish

•

French

•

French-Canadian

•

Italian

•

Korean

•

Dutch

•

Norwegian

•

Portuguese

•

Portuguese-Brazilian

•

Russian

•

Swedish

•

Chinese - Mandarin 

•

Chinese- Cantonese 

(IP Office 4.2

+)

•

For full details of embedded voicemail setup and configuration, refer to the Embedded Voicemail Installation manual.

•

Memory cards in these slots can also be used for storage of files normally obtained via TFTP transfer. For example the
music-on-hold wav file and supported 4600 Series/5600 Series software files. This will however reduce storage space
for prompt and message files if embedded voicemail is being used. Non-Avaya memory cards can be used for this
function.

 

Summary of Contents for IP Office Phone Manager




























































































































































































































































































































































































































Reviews:

No comments