manualshive.com logo in svg

Avaya IP Office Phone Manager, Installation Manual, Page: 365 / 411

Share
Download
Avaya IP Office Phone Manager Installation Manual Download Page 365

IP Office Installation

Page 364

15-601042 Issue 20b (16 July 2009)

IP Office

10.12.16 V.24 WAN Cable

This cable is used for connection an IP Office 37-way D-type WAN port to the V.24 WAN service providers equipment.

IP Office
WAN Port

Signal

V.24 WAN
Service

6

Ground

7

8

DTR: Data Terminal Ready.

20

9

Rx: Receive Data

3

10

Tx: Transmit Clock

15

11

DCD: Data Carrier Detect.

8

12

CTS: Clear To Send.

5

26

Tx: Transmit Data.

2

27

RTS: Request To Send.

4

28

Rx-Clk: Receive Clock.

17

29

RI: Ring Indicator.

22

30

DSR: Data Set Ready.

6

•

At the IP Office end pin 25 is connected to pin 6.

•

At the IP Office end pin 19 is connected to the Screened Cable
Drain Wire.

 

•

Supply: This cable is not supplied with the control unit or WAN3 module. It must be ordered separately.

•

SAP Code: 700213416

•

Cable: 12-core screened cable. Each core is 7/0.203mm (24 AWG) tinned copper stranded wire, nominal capacitance
of 95pF/m, resistance of 92 ohms/km, screened with tinned copper braid, maximum working voltage of 440V rms and
a maximum current per core of 1A rms. The maximum core to core capacitance must not exceed 800pF.

•

Maximum Length: 5m/16'5''. This is the maximum length that should be used if the above cable is replaced with an
alternate cable.

 

Summary of Contents for IP Office Phone Manager




























































































































































































































































































































































































































Reviews:

No comments