manualshive.com logo in svg

Avaya IP Office Phone Manager, Installation Manual, Page: 10 / 411

Share
Download
Avaya IP Office Phone Manager Installation Manual Download Page 10

IP Office Installation

Page 9

15-601042 Issue 20b (16 July 2009)

IP Office

Installing IP Office:  

1. Installing IP Office

This documentation is intended to assist with the installation of the core components of an Avaya IP Office telephone
system. It describes those components and factors that should be considered for an installation.

•

The IP Office is a converged voice and data communications system. It should therefore only be installed by persons
with telephony and IP data network experience.

•

Installers must be trained on IP Office systems. Through its Avaya University (AU), Avaya provides a range of training
courses including specific IP Office implementation and installation training. It also provides certification schemes for
installers to achieve various levels of IP Office accreditation. See Training.  

•

It is the installer’s responsibility to ensure that all installation work is done in accordance with local and national
regulations and requirements. It is also their responsibility to accurately establish the customer’s requirements before
installation and to ensure that the installation meets those requirements.

•

You should read and understand this documentation before installation. You should also obtain and read the Avaya
Technical Bulletins relevant to recent IP Office software and hardware releases to ensure that you are familiar with any
changes to the IP Office equipment and software.

 

The following components of IP Office are outside the range of a basic IP Office installation. They are covered by separate
installation and configuration documentation. If those components are to be part of the IP Office system installation, that
documentation should be obtained, read and understood prior to the installation.

•

4600/5600 Series IP Phone Installation.

•

Embedded Voicemail Installation.

•

Voicemail Pro Installation.

•

Delta Server (SMDR) Installation.

•

Compact Business Center (CBC) Installation.

•

Compact Contact Center (CCC) Installation.

•

Contact Store Installation.

•

Compact DECT Installation.

•

IP DECT Installation.

•

3600 Series Wireless IP Installation.

•

Phone Manager Installation Manual. 

•

SoftConsole Installation Manual. 

•

Conferencing Center Installation Manual. 

Summary of Contents for IP Office Phone Manager




























































































































































































































































































































































































































Reviews:

No comments