manualshive.com logo in svg

Avaya IP Office Phone Manager, Installation Manual, Page: 116 / 411

Share
Download
Avaya IP Office Phone Manager Installation Manual Download Page 116

IP Office Installation

Page 115

15-601042 Issue 20b (16 July 2009)

IP Office

IP400 Basic Installation: Control Unit Power Up

6.4 Connecting the Manager PC

At this stage we will directly connect the Manager PC to the new IP Office control unit. For this the PC will need to be set
to a fixed IP address in the same subnet range as the IP Office control unit's default address
(192.168.42.1/255.255.255.255).

 

Objective -

 Physically connecting the Manager PC and the IP Office without needing to adjust or configure any

intervening equipment.

 

Parts and Equipment Required

•

o

 

Manager PC

.

•

o

 

LAN Cable

.

•

o

 

IP Office Small Office Edition, IP406 V2 and IP500 control units:

 

A standard RJ45-RJ45 LAN cable can be used.

•

o

 

IP412 Control Unit:

 

A RJ45-RJ45 cross-over LAN cable is required.  

 

 

Procedure: Direct Connection to a Defaulted IP Office Control Unit

1. Check that the TCP/IP properties for the Manager PC's Local Area Network connection are set as follow:

•

Fixed IP address: 

192.168.42.203

•

Subnet mask:

 255.255.255.0

•

Default gateway:

 192.168.42.1.

2. Connect the LAN cable from the PC's LAN port the LAN 1 port on the IP Office control unit.

3. Check that the orange LED lamp on the IP Office LAN port is on. The green LED may also be flickering as it

indicates traffic across the LAN connection.

4. Select 

Start | Run

 and enter 

cmd

.

5. In the command window that appears enter ping 192.168.42.1. The results should show a number of ping replies

from the IP Office. This confirms basic communication between the Manager PC and the IP Office.

6. If there are no ping replies enter 

ipconfig

. The results should list the IP address settings of the Manager PC as

required above and with no mention of DHCP being used. Enter exit.

7. Check the cable connection.

 

Summary of Contents for IP Office Phone Manager




























































































































































































































































































































































































































Reviews:

No comments