manualshive.com logo in svg

Avaya IP Office Phone Manager, Installation Manual, Page: 360 / 411

Share
Download
Avaya IP Office Phone Manager Installation Manual Download Page 360

IP Office Installation

Page 359

15-601042 Issue 20b (16 July 2009)

IP Office

System Components: Physical Ports

10.12.11 LAN Port

These ports are found on IP Office control units and the WAN3 10/100 expansion module. They are used for connection
to IP LAN's and IP devices. On the WAN3 10/100 module the port is used for direct connection to a control unit.

All IP Office LAN ports are 10/100Mbps auto-sensing. Operation varies as follows:

•

IP Office 500

 

This unit has 2 RJ45 Ethernet ports, marked as LAN and WAN. These form a full-duplex managed layer-3 switch.
Within the IP Office configuration, the physical LAN port is LAN1, the physical WAN port is LAN2.

•

IP460 V2

 

This unit has 8 RJ45 Ethernet ports marked as LAN 1 to 8. These form a full-duplex unmanaged layer-2 LAN switch.
Ports are auto-MDI/MDIX. Within the IP Office configuration the physical LAN ports are LAN1.

•

IP412

 

This unit has 2 RJ45 Ethernet ports marked as LAN 1 to 2. These form a half-duplex managed layer-3 switch. Both
ports are fixed MDI crossover ports. Within the IP Office configuration, physical port 1 is LAN1, physical port 2 is LAN2.

•

Small Office Edition

 

This unit has 4 RJ45 Ethernet ports marked LAN 1 to 4. These form a full-duplex unmanaged layer-2 switch. An
addition RJ45 Ethernet socket marked as WAN exists. With the LAN ports this acts as a managed layer-3 switch. Within
the IP Office configuration, the physical LAN ports are LAN1, the physical WAN port is LAN2.

 

The LAN port LED's are used as follows:

•

Green: On = connected, Flashing = Activity.

•

Yellow: On = 100Mbps, Off = 10Mbps.

 

LAN Cables 

These are CAT5 UTP cables for connection of various IP devices within the IP Office system.

IP Office

 

 

LAN

Pin

MDIX

(Normal)

MDI

(Crossover)

Wire

Standard/

Interconnect

Crossover

 

1

Rx-A.

Tx-A.

White/Orange

1

3

 

2

Rx-B.

Tx-B.

Orange/White

2

6

3

Tx-A.

Rx-A.

White/Green

3

1

4

Not used.

Not used.

Blue/White

4

4

5

Not used.

Not used.

White/Blue

5

5

6

Tx-B.

Rx-B.

Green/White

6

2

7

Not used.

Not used.

White/Brown

7

7

8

Not used.

Not used.

Brown/White

8

8

•

SAP Code:

 

•

LAN Cable - GREY: 700213481.

 

Standard straight LAN cable.  

•

LAN Interconnect Cable - Green: 700213465. 

Supplied with WAN3 modules for the direct connection of the WAN3 module to an IP Office control unit LAN port. For
an IP412 control unit, this cable should be replaced with a LAN crossover cable.

•

LAN Crossover Cable - Black: 700213473.

 

LAN crossover cable.

 

Summary of Contents for IP Office Phone Manager




























































































































































































































































































































































































































Reviews:

No comments