manualshive.com logo in svg

Avaya IP Office Phone Manager, Installation Manual, Page: 204 / 411

Share
Download
Avaya IP Office Phone Manager Installation Manual Download Page 204

IP Office Installation

Page 203

15-601042 Issue 20b (16 July 2009)

IP Office

System Components: Control Units

Ports

Description

AUDIO

3.5mm Stereo jack socket. Used for external music on hold source input.

DC I/P

DC power input port. Used for connection of the power lead from an Avaya earthed 60W external
power supply unit supplied with the control unit.

DTE

9-Way D-Type socket. Used for system maintenance. Suitable for direct connection of IP Office Serial
Port Feature Key dongle.

EXPANSION

RJ45 socket. Used for direct connection to external expansion modules using the Expansion
Interconnect cable supplied with the expansion module.

EXT O/P

3.5mm Stereo jack socket. Used for switching external relay systems such as door entry controls. The
port contains two independent switches controlled by the IP Office.

LAN

RJ45 socket. These ports form a managed layer 3 Ethernet switch. The ports are half-duplex
10/100Mbps auto-sensing, MDI crossover ports.

SLOT A

Used for trunk cards of all types except WAN port trunk card. Normally Slot B should be used first.
Trunks cards are supplied with replacement external blanking plates suitable for the trunk card port
connections.

SLOT B

WAN

37-Way D-Type socket. Used for the connection of V.24, V.35 or X.21 WAN service.

Used for connection of a 

function or protective ground

. Use of a ground for all systems is

recommended and for some locales may be a regulatory requirement. On older modules where this
screw is not present, the left-hand fixing screw of Slot B can be used.

All control units are available in either North America or Rest of World variants. The choice controls various default
settings of the unit. For E911 support a North American variant control unit must be used. The companding can be
changed once a unit is installed. Control units are supplied with an external power supply unit but not a locale specific
power cord.    

Item

Variant

Country

SAP Code

IP412 Office

A-Law

Rest of World

700234479

U-Law

North America

700350408

IEC60320 C13 Power Cord

CEE7/7

Europe

700289762

BS1363

United Kingdom

700289747

NEMA5-15P

America

700289770

China

China

700261977

IP400 Rack Mounting Kit

All

700210800

 

Summary of Contents for IP Office Phone Manager




























































































































































































































































































































































































































Reviews:

No comments