manualshive.com logo in svg

Avaya IP Office Phone Manager, Installation Manual, Page: 167 / 411

Share
Download
Avaya IP Office Phone Manager Installation Manual Download Page 167

IP Office Installation

Page 166

15-601042 Issue 20b (16 July 2009)

IP Office

9. Additional Processes

9.1 Upgrading the Core Software

The installed IP Office Manager includes 

.bin core software

 files appropriate to the software level. It can be used to load

those .bin file into the control unit and modules within the IP Office system.

 

 

WARNINGS

•

Check IP Office Technical Bulletins

 

Check the latest IP Office Technical Bulletin for the IP Office software release before proceeding any further. It
may contain information relating to changes that occurred after this document was completed. Bulletins are
available from http://support.avaya.com.

•

WAN3 10/100 Modules

 

Upgrade each WAN3 10/100 module separately and only after having upgraded the control unit and any other
expansion modules.   

•

Upgrading pre-Level 2.1 Systems

 

For IP Office Systems with software Level 2.0 or earlier, the upgrade procedure must be done from a PC with a
fixed IP address on the same subnet and LAN segment as the IP Office.

•

Multi-Stage Upgrades

 

Due to the need to adjust internal memory allocation and configuration storage, for some upgrades the control
unit may need to perform multi-stage upgrade process. The table below indicates the require upgrade paths.

Control Unit

.bin File

Unvalidated 
Only

Validated

IP406 V2

ip406u.bin

–

2.1 > 3.0 > 3.0(999) > 3.1 > 3.1(999) > 3.2 > 5.0.

IP412

ip412.bin

1.3 > 2.1

2.1 > 3.0 > 3.1 > 3.2 > 5.0.

IP500

ip500.bin

–

4.0.0 > 5.0.

•

Multiple Managers

 

If more than one copy of Manager is running it is possible for the IP Office to request BIN files from a different
Manager from the one that started the upgrade process. Ensure that only one copy of Manager is running when
upgrading an IP Office system.

•

Other IP Office Applications

 

Upgrading the core software of the IP Office control unit may require upgrades to associated software. Typically IP
Office is compatible with the previous release of most IP Office applications, however for each IP Office core
software release there may be exceptions. These exceptions will be detailed in the Technical Bulletin for the IP
Office core software release.

 

Information Required

•

o

 

System Password

 - For a new or defaulted system this is password.

 

 

Tools Required

•

o

 

Manager PC

 - The Upgrade Wizard tool is part of the Manager application.  

Summary of Contents for IP Office Phone Manager




























































































































































































































































































































































































































Reviews:

No comments