Mitsubishi Electric FR-E800, Инструкция по эксплуатации, Страница: 33 / 484

32
2. Basic Operation
2.4 Frequently-used parameters (simple mode parameters)
*1 Initial value for the FR-E820-0050(0.75K) or lower, FR-E840-0026(0.75K) or lower, and FR-E820S-0050(0.75K) or lower.
Pr.
Pr.
group
Name Increment
Initial value
*9
Range Application
Refer
to
page
Gr.1 Gr.2
0 G000 Torque boost 0.1%
6%
*1
0% to 30%
Set this parameter to obtain a higher starting
torque under V/F control. Also set this when a
loaded motor cannot be driven, the warning
"OL" occurs, and the inverter output is shut off
with the fault indication "E.OC1".
426
5%
*2
4%
*3
3%
*4
2%
*5
1 H400 Maximum frequency 0.01 Hz 120 Hz 0 to 120 Hz Set the upper limit for the output frequency.
253
2 H401 Minimum frequency 0.01 Hz 0 Hz 0 to 120 Hz Set the lower limit for the output frequency.
3 G001 Base frequency 0.01 Hz 60 Hz 50 Hz 0 to 590 Hz
Set this parameter when the rated motor
frequency is 50 Hz. Check the rating plate of
the motor.
428
4 D301
Multi-speed setting
(high speed)
0.01 Hz 60 Hz 50 Hz 0 to 590 Hz
Pre-set the speeds that will be switched
among by terminals.
35 ,
40 ,
234
5 D302
Multi-speed setting
(middle speed)
0.01 Hz 30 Hz 0 to 590 Hz
6 D303
Multi-speed setting
(low speed)
0.01 Hz 10 Hz 0 to 590 Hz
7 F010 Acceleration time 0.1 s
5 s
*6
0 to 3600 s Set the acceleration time.
196
10 s
*7
8 F011 Deceleration time 0.1 s
5 s
*6
0 to 3600 s Set the deceleration time.
10 s
*7
9
H000
C103 Electronic thermal
O/L relay
0.01 A
Inverter rated
current
*8
0 to 500 A
Protects the motor from heat. Set the rated
motor current.
238
79 D000
Operation mode
selection
1 0 0 to 4, 6, 7
Select the start and frequency command
sources.
212
125 T022
Terminal 2
frequency setting
gain frequency
0.01 Hz 60 Hz 50 Hz 0 to 590 Hz
Change the frequency at the maximum
potentiometer setting (5 V in the initial
setting).
42 ,
318
126 T042
Terminal 4
frequency setting
gain frequency
0.01 Hz 60 Hz 50 Hz 0 to 590 Hz
Change the frequency at the maximum
current input (20 mA in the initial setting). 44 ,
318
160 E440
User group read
selection
1 0 0, 1, 9999
This function restricts the parameters that are
read by the operation panel and parameter
unit.
102
313 M410
DO0 output
selection
1 9999
Refer to page
270 .
Set this parameter to assign the functions to
the devices RX9 to RXB for the CC-Link IE
TSN and CC-Link IE Field Network Basic.
*10
314 M411
DO1 output
selection
1 9999
315 M412
DO2 output
selection
1 9999
349 N010
Communication
reset selection
1 0 0, 1
Disable an error reset command given via
communication in the External operation
mode or the PU operation mode.
*10
541 N100
Frequency
command sign
selection
1 0 0, 1
Set this parameter to make the start
command (forward/reverse rotation) inverted
by adding a plus or minus sign to the value of
the frequency command sent through the CC-
Link IE TSN or the CC-Link IE Field Network
Basic.
*10
544 N103
CC-Link extended
setting
1 0
0, 1, 12, 14,
18, 24, 28
Set this parameter to extend the function of
the remote registers for the CC-Link IE TSN or
the CC-Link IE Field Network Basic.
*10
998 E430
PM parameter
initialization
1 0
0, 8009,
8109, 9009,
9109 Select the PM sensorless vector control and
set the parameters that are required to drive a
PM motor.
102
999 E431
Automatic
parameter setting
1 9999
10, 12, 20,
21, 9999
Changes parameter settings as a batch. The
target parameters include communication
parameters for the Mitsubishi Electric human
machine interface (GOT) connection and the
parameters for the rated frequency settings of
50/60 Hz.
179