258
11. (H) Protective Function Parameters
11.10 Stall prevention operation
Disabling the stall prevention operation and fast-response current limit
according to operating conditions (Pr.156)
• Referring to the following table, enable/disable the stall prevention operation and the fast-response current limit operation,
and also set the operation at OL signal output.
*1
When "operation stop at OL signal output" is selected, the fault output "E.OLT" (stop due to stall prevention) is displayed, and operation stops.
*2
The OL signal and E.OLT are not output because fast-response current limit and stall prevention are not operating.
*3
Setting values "100, 101" can be individually set for power driving and regenerative driving. The setting value "101" disables the fast-response
current limit during power driving.
NOTE
• When the load is heavy or the acceleration/deceleration time is short, stall prevention operates and acceleration/deceleration
may not be performed according to the time set. Set the
Pr.156
and stall prevention operation level to the optimum values.
• For lift applications, make settings to disable the fast-response current limit. Otherwise, the torque may be insufficient, causing
the load to drop.
Pr.156 setting
Fast-response
current limit
○
: enabled
●
: disabled
Stall prevention operation selection
○
: enabled
●
: disabled
Operation during
stall prevention
○
: continued
●
: stopped
Acceleration
Constant speed
Deceleration
0 (initial value)
○
○
○
○
○
1
●
○
○
○
○
2
○
●
○
○
○
3
●
●
○
○
○
4
○
○
●
○
○
5
●
○
●
○
○
6
○
●
●
○
○
7
●
●
●
○
○
8
○
○
○
●
○
9
●
○
○
●
○
10
○
●
○
●
○
11
●
●
○
●
○
12
○
○
●
●
○
13
●
○
●
●
○
14
○
●
●
●
○
15
●
●
●
●
16
○
○
○
○
●
17
●
○
○
○
●
18
○
●
○
○
●
19
●
●
○
○
●
20
○
○
●
○
●
21
●
○
●
○
●
22
○
●
●
○
●
23
●
●
●
○
●
24
○
○
○
●
●
25
●
○
○
●
●
26
○
●
○
●
●
27
●
●
○
●
●
28
○
○
●
●
●
29
●
○
●
●
●
30
○
●
●
●
●
31
●
●
●
●
100
Power driving
○
○
○
○
○
Regenerative driving
●
●
●
●
101
Power driving
●
○
○
○
○
Regenerative driving
●
●
●
●
Содержание FR-E800
