Mitsubishi Electric FR-E800, Инструкция по эксплуатации

Страница: 331 / 484

330
13. (T) Multi-Function Input Terminal Parameters
13.6 Input terminal function selection
*1 When Pr.59 Remote function selection ≠ "0", functions of the RL, RM, and RH signals are changed as shown in the table.
*2 When Pr.270 Stop-on-contact control selection = "1 or 11", functions of the RL and RT signals are changed as shown in the table.
*3 The OH signal is activated when the relay contact is open.
NOTE
• The same function can be assigned to two or more terminals. In this case, the logic of terminal input is OR.
• The priorities of the speed commands are defined as follows: JOG > multi-speed setting (RH, RM, RL, REX) > PID (X14).
• When the Inverter run enable (X10) signal is not assigned, or when the PU operation external interlock (X12) signal is not
assigned while Pr.79 Operation mode selection = "7", the MRS signal performs the same function.
• The same terminals are used to assign the multi-speed (7-speed) setting and the remote setting. The multi-speed setting and
the remote setting cannot be assigned separately.
• When the terminal assignment is changed using Pr.178 to Pr.189 (Input terminal function selection) , wiring may be
mistaken due to different terminal name and signal contents, or may affect other functions. Set parameters after confirming
the function of each terminal.
 Parameters available for each signal
• The following table shows the parameters to which the signals are assigned.
9999 - No function — —
Setting
Signal
name
Function Related parameter
Refer to
page
Setting
value
Signal
name
FR-E800 FR-E800-E
FR-E800-
SCE
Pr.178 Pr.179
Pr.180 to
Pr.184
Pr.185 to
Pr.189
Pr.178 Pr.179
Pr.180 to
Pr.189
Pr.180 to
Pr.189
0 RL ○ ○ ○ ○ ○ ○ ○ ○
1 RM ○ ○ ○ ○ ○ ○ ○ ○
2 RH ○ ○ ○ ○ ○ ○ ○ ○
3 RT ○ ○ ○ ○ ○ ○ ○ ○
4 AU ○ ○ ○ ○ ○ ○ ○ ○
5 JOG ○ ○ ○ — ○ ○ — —
7 OH ○ ○ ○ — ○ ○ — —
8 REX ○ ○ ○ ○ ○ ○ ○ ○
10 X10 ○ ○ ○ — ○ ○ — —
12 X12 ○ ○ ○ — ○ ○ — —
13 X13 ○ ○ ○ ○ ○ ○ ○ ○
14 X14 ○ ○ ○ ○ ○ ○ ○ ○
15 BRI ○ ○ ○ ○ ○ ○ ○ ○
16 X16 ○ ○ ○ — ○ ○ — —
18 X18 ○ ○ ○ ○ ○ ○ ○ ○
23 LX ○ ○ ○ ○ ○ ○ ○ ○
24 MRS ○ ○ ○ ○ ○ ○ ○ ○
25
STP
(STOP)
○ ○ ○ — ○ ○ — —
26 MC ○ ○ ○ ○ ○ ○ ○ ○
27 TL ○ ○ ○ ○ ○ ○ ○ ○
30 JOG ○ ○ ○ ○ ○ ○ ○ ○
37 X37 ○ ○ ○ ○ ○ ○ ○ ○
42 X42 ○ ○ ○ ○ ○ ○ ○ ○
43 X43 ○ ○ ○ ○ ○ ○ ○ ○
46 TRG ○ ○ ○ ○ ○ ○ ○ ○
47 TRC ○ ○ ○ ○ ○ ○ ○ ○
50 SQ ○ ○ ○ ○ ○ ○ ○ ○
51 X51 ○ ○ ○ ○ ○ ○ ○ ○
60 STF ○ — — — ○ — — —
61 STR — ○ — — — ○ — —
62 RES ○ ○ ○ — ○ ○ — —
65 X65 ○ ○ ○ — ○ ○ — —
66 X66 ○ ○ ○ — ○ ○ — —
67 X67 ○ ○ ○ — ○ ○ — —
72 X72 ○ ○ ○ ○ ○ ○ ○ ○