Mitsubishi Electric FR-E800, Инструкция по эксплуатации

Страница: 295 / 484

294
12. (M) Item and Output Signal for Monitoring
12.6 Output terminal function selection
12 112 Y12 Output current detection
Output when the output current is higher
than the
Pr.150 setting for the time set in
Pr.151 or longer.
Pr.150, Pr.151 304
13 113 Y13 Zero current detection
Output when the output current is lower than
the
Pr.152 setting for the time set in Pr.153
or longer.
Pr.152, Pr.153 304
14 114 FDN PID lower limit
Output when the input value is lower than
the lower limit set for the PID control
operation.
Pr.127 to
Pr.134, Pr.575
to Pr.577
380
15 115 FUP PID upper limit
Output when the input value is higher than
the upper limit set for the PID control
operation.
16 116 RL
PID forward/reverse
rotation output Output during forward rotation operation in
the PID control operation.
20 120 BOF Brake opening request
Output to release the brake while the brake
sequence function is enabled. Pr.278 to
Pr.285, Pr.292
370
25 125 FAN Fan fault output Output when a fan fault occurs. Pr.244 245
26 126 FIN
Heat sink overheat pre-
alarm
Output when the heat sink temperature rises
to 85% of temperature at which the
protective function of the Heat sink overheat
is activated.
—
Instruction
Manual
(Maintenance)
30 130 Y30
Forward rotation output
(output for a Vector
control compatible
option)
*2
Output while a motor rotates in forward
direction.
—
299
31 131 Y31
Reverse rotation output
(output for a Vector
control compatible
option)
*2
Output while a motor rotates in reverse
direction.
299
32 132 Y32
Regenerative status
output (output for a Vector
control compatible
option)
*2
Output while a motor is in a regenerative
braking state under Vector control.
299
33 133 RY2 Operation ready 2
Output while pre-excitation is enabled or
during normal operation under Real
sensorless vector control, Vector control, or
PM sensorless vector control.
— 296
34 134 LS Low speed detection
Output when the output frequency drops to
the
Pr.865 setting or lower.
Pr.865 301
35 135 TU Torque detection
Output when the motor torque is higher than
the
Pr.864 setting.
Pr.864 306
39 139 Y39
Start time tuning
completion
Output when the start-time tuning complete. Pr.95, Pr.574 362
40 140 Y40 Trace status Output during trace operation.
Pr.1020,
Pr.1022 to
Pr.1047
418
41 141 FB Speed detection
Output when the actual motor rotations per
minute (estimate) reaches the setting of
Pr.42 .
Pr.42 301
44 144 RUN2 Inverter running 2
Output while the Forward rotation command
signal or Reverse rotation command signal
is ON. Output during deceleration even
while the Forward rotation command signal
or Reverse rotation command signal is OFF
— 296
45 145 RUN3
Inverter running and start
command ON Output while the inverter is running or while
the start command signal is ON.
— 296
46 146 Y46
During deceleration at
occurrence of power
failure
Output when the power-failure deceleration
function is activated.
(The signal output is retained until the
function stops.)
Pr.261 414
47 147 PID
During PID control
activated
Output during the PID control operation.
Pr.127 to
Pr.134, Pr.575
to Pr.577
380
Setting
Signal
name
Function Operation
Related
parameter
Refer to page
Positive
logic
Negative
logic