Mitsubishi Electric FR-E800, Инструкция по эксплуатации

Страница: 228 / 484

1
2
3
4
5
6
7
8
9
10
227
10. (D) Operation Command and Frequency Command
10.3 Start command source and frequency command source during communication operation
○ : Controllable, ×: Uncontrollable, Δ : Partially controllable, —: No function
*1 Operation when the enclosure surface operation panel (FR-PA07) is used.
*2 RS-485 communication via PU connector
*3 Only PU stop is enabled. "PS" is displayed on the operation panel during PU stop. The operation follows the Pr.75 Reset selection/
disconnected PU detection/PU stop selection setting. (Refer to page 161 .)
*4 The operation follows the Pr.338 Communication operation command source and Pr.339 Communication speed command source
settings. (Refer to page 223 .)
*5 Writing of some parameters may be disabled by the Pr.77 Parameter write selection setting and the operating condition. (Refer to page 173 .)
USB
connector
Pr.551 = "3, 9999"
Operation command
(start, stop)
○ × × ○ × ×
Frequency setting ○ × ○ × × ×
Monitor ○ ○ ○ ○ ○ ○
Parameter write
○
*5
×
*6
○ ○
×
*6
×
*6
Parameter read ○ ○ ○ ○ ○ ○
Inverter reset ○ ○ ○ ○ ○ ○
Other than the
above
Operation command
(start, stop)
× × × × × ×
Frequency setting × × × × × ×
Monitor ○ ○ ○ ○ ○ ○
Parameter write
×
*6
×
*6
×
*6
×
*6
×
*6
×
*6
Parameter read ○ ○ ○ ○ ○ ○
Inverter reset ○ ○ ○ ○ ○ ○
Option
Pr.550 = "0, 9999"
Operation command
(start, stop)
× × × × —
○
*4
Frequency setting × × × × —
○
*4
Monitor ○ ○ ○ ○ ○ ○
Parameter write
×
*6
×
*6
×
*6
×
*6
—
○
*5
Parameter read ○ ○ ○ ○ ○ ○
Inverter reset × × × ×
×
*6
○
Other than the
above
Operation command
(start, stop)
×
*6
×
*6
×
*6
×
*6
×
*6
—
Frequency setting
×
*6
×
*6
×
*6
×
*6
×
*6
—
Monitor ○ ○ ○ ○ ○ ○
Parameter write
×
*6
×
*6
×
*6
×
*6
— ○
Parameter read ○ ○ ○ ○ ○ ○
Inverter reset
×
*6
×
*6
×
*6
×
*6
×
*6
—
Ethernet
connector
Pr.550 = "5" or
Pr.550 = "9999"
(communication
option is not
installed)
Operation command
(start, stop)
× × × × ○ —
Frequency setting × × × × ○ —
Monitor ○ ○ ○ ○ ○ ○
Parameter write
×
*6
×
×
*6
×
*6
○
*5
—
Parameter read ○ ○ ○ ○ ○ ○
Inverter reset × × × ×
○
*7
—
Other than the
above
Operation command
(start, stop)
× × × × — ×
Frequency setting × × × × — ×
Monitor ○ ○ ○ ○ ○ ○
Parameter write × × × × —
×
*6
Parameter read ○ ○ ○ ○ ○ ○
Inverter reset × × × × — ×
External
control
circuit
terminal
—
Operation command
(start, stop)
× ○ ○ ×
×
*4
×
*4
Frequency setting × ○
Δ
*8
○
×
*4
×
*4
Inverter reset ○ ○ ○ ○ ○ ○
Command
interface
Condition Item
Controllability in each operation mode
PU
operation
External
operation
Combined
operation
mode 1
(Pr.79 = "3")
Combined
operation
mode 2
(Pr.79 = "4")
NET
operation
(when the
PU/Ethernet
connector
is used)
NET
operation
(via option)