Keysight E6650A EXF Скачать руководство пользователя страница 249 | Manualshive

Страница: 249 / 657

background image

6 List Sequence Measurements

List Sequence Measurements

69. Minimum margin from the limit line on the negative offset D (db)

70. Minimum margin from the limit line on the positive offset D (db)

71. Minimum margin from the limit line on the negative offset E (db)

72. Minimum margin from the limit line on the positive offset E (db)

73. Minimum margin from the limit line on the negative offset F (db)

74. Minimum margin from the limit line on the positive offset F (db)

The unit for the absolute power results (listed in italics) varies depending on the Measurement
Type:

If the measurement type is Total Power Reference, these results are expressed in dBm

If the measurement type is Power Spectral Density Reference, these results are expressed in
dBm/Hz

parameter_table_23.52941

52.94118

Key Path

Meas

Initial S/W Revision

A.05.00

Help Map ID

0

WLAN SEM Trace Results

WLAN SEM Trace results are detailed here.

These results are part of WLAN SEM measurement, and they can be querried by
MEAS|READ|FETCh:LSEQuencer:ACQuire{1...512}:ASTep{1...1000}:WLAN:SEM:TRACe? Or Async fetch
:FETCh:LSEQuencer:ASYNc:ACQuire{1:512}:ASTep{1:1000}:WLAN:SEM:TRACe? These scpi commands
are only available when WLAN SEM measurement is configured in the specified analysis step.

WLAN SEM Trace results return the frequency domain spectrum trace data, separated by comma. The
number of data points is 3001.

Occupied Bandwidth Results

If the analysis step has requested this measurement then the results returned for the analysis step within
the List Sequencer measurement are listed below.

For more information on each result see the online help for the relevant radio standard measurement
mode.

The SCPI-only header values are as follows:

Meas Bitmap Header is a floating point number which appears ahead of the results for the analysis
interval; it is a decimal representation of the meas bitmap value for the measurements included in the
interval. The value returned for OBW results is 1024. If more than one measurement is included in this
analysis step, then the value returned represents the combined meas bitmap value for all included
measurements, and the results are returned in ascending order of their meas bitmap values.

Sequence Analyzer User's & Programmer's Reference

249

«
...
247
248
249
250
251
...
»

Содержание E6650A EXF


















































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для E6650A EXF

Бренд: Landoll Страницы: 52

Бренд: JBSYSTEMS Light Страницы: 14

Бренд: YardShape Страницы: 50

Бренд: ICS ELECTRONICS Страницы: 6

Бренд: Panasonic Страницы: 174

Бренд: Backyard Discovery Страницы: 51

Бренд: Nautilus Страницы: 12

Бренд: CAIRE Страницы: 16

Бренд: Parker Страницы: 64

Бренд: Parker Страницы: 40

Matrx Digital MDM

Бренд: Parker Страницы: 20

HQ Power VDL25BM

Бренд: Velleman Страницы: 3

Бренд: iGuzzini Страницы: 36

AQUIS ULTRAFLOW

Бренд: Waterous Страницы: 56

Бренд: Zennio Страницы: 3

Бренд: Task Force Tips Страницы: 16

AURO SPOT CLAS100

Бренд: Cameo Страницы: 60

Бренд: Daihan Scientific Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды