Keysight E6650A EXF Скачать руководство пользователя страница 167 | Manualshive

Страница: 167 / 657

background image

5 System Functions

System

An instrument can never power up for the first time in Last.
If line power to the analyzer is interrupted, for example by pulling the line cord plug or by switching off
power to a test rack, Power On Last State may not work properly. For proper operation, Power On Last
State depends on you shutting down the instrument using the Standby key or the SYSTem:PDOWn SCPI
command. This will ensure the last state of each mode is saved and can be recalled during a power up.

Key Path

System, Power On

Mode

All

Example

SYST:PON:TYPE LAST

Notes

Power on Last State only works if you have done a controlled shutdown prior to powering on in Last.
If a controlled shutdown is not done when in Power On Last State, the instrument will power up in
the last active mode, but it may not power up in the active mode’s last state. If an invalid mode state
is detected, a Mode Preset will occur. To control the shutdown under remote control use the
:SYSTem:PDOWn command.

Readback Text

Last State

Backwards Compatibility
Notes

It is no longer possible to power-up the analyzer in the last mode the analyzer was running with that
mode in the preset state. (ESA/PSA SYST:PRESET:TYPE MODE with SYST:PON:PRESET) You can
power-on the analyzer in the last mode the instrument was running in its last state (SYST:PON:TYPE
LAST), or you can specify the mode to power-up in its preset state (SYST:PON:MODE <mode>).

Initial S/W Revision

Prior to A.02.00

Power On Application

Accesses a menu that lists the available Modes and lets you select which Mode is to be the power-on
application.

This application is used for Power On Type “Mode and Input/Output Defaults” and Restore System
Defaults All.

Key Path

System, Power On

Mode

All

Remote Command

:SYSTem:PON:MODE SA | BASIC | ADEMOD | NFIGURE | PNOISE | CDMA2K |
TDSCDMA | VSA | VSA89601 | WCDMA | WIMAXOFDMA

:SYSTem:PON:MODE?

Example

SYST:PON:MODE SA

Notes

The list of possible modes (and remote parameters) to choose from is dependent on which modes are
installed in the instrument.

Preset

This is unaffected by a Preset but is set on a “Restore System Defaults->All” to:

State Saved

No

Initial S/W Revision

Prior to A.02.00

Sequence Analyzer User's & Programmer's Reference

167

«
...
165
166
167
168
169
...
»

Содержание E6650A EXF


















































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для E6650A EXF

WJHD309A - DIGITAL DISK RECORDER

Бренд: Panasonic Страницы: 79

Бренд: NAD Страницы: 10

Бренд: B&G Страницы: 3

Бренд: Xiitech Страницы: 6

Pressure Governor

Бренд: Waterous Страницы: 53

Бренд: Landi Renzo Страницы: 16

Бренд: IBM Страницы: 163

Бренд: Aspect Medical Systems Страницы: 104

Бренд: Hupfer Страницы: 153

CHIEFTAIN E1006

Бренд: Falcon Страницы: 5

500 FleetBroadband

Бренд: Sailor Страницы: 20

Бренд: Gomaco Страницы: 30

Бренд: Panduit Страницы: 4

Бренд: B-Safety Страницы: 2

Бренд: ZAMST Страницы: 14

Бренд: Elliott Страницы: 46

Бренд: KUHN Страницы: 44

BoilerMag XT Series

Бренд: Spear & Jackson Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды