Keysight E6650A EXF Скачать руководство пользователя страница 120 | Manualshive

Страница: 120 / 657

Keysight E6650A EXF Скачать руководство пользователя страница 120

3 Input/Output Functions
Input/Output

Preset

RFIO4

State Saved

Saved in State

Initial S/W Revision

A.14.00

Output Config

Accesses keys that configure various output settings, like the frequency reference output, trigger output
and analog output.

Key Path

Input/Output

Backwards Compatibility
Notes

In ESA there was not a user interface to enable the Video Output (Analog Output), Trigger Output, or

Gate Output. In the X-Series each of these physical connectors requires configuration, thus the
user interface has been added for X-Series, along with the potential for an output you think is
always on to be switched off.

Initial S/W Revision

Prior to A.02.00

Trig Out

Select the type of output signal that will be output from the Trig 1 Out, or Trig 2 Out connectors.

Key Path

Input/Output, Output Config

Remote Command

:TRIGger|TRIGger1|TRIGger2[:SEQuence]:OUTPut HSWP | MEASuring | MAIN |
GATE | GTRigger | OEVen | SPOint | SSWeep | SSETtled | S1Marker |
S2Marker | S3Marker | S4Marker | OFF

:TRIGger|TRIGger1|TRIGger2[:SEQuence]:OUTPut?

Example

TRIG:OUTP HSWP

TRIG2:OUTP GATE

Dependencies

The second Trigger output (Trig 2 Out) does not appear in all models; in models that do not support it,
the Trig 2 Out key is blanked, and sending the SCPI command for this output generates an error,
“Hardware missing; Not available for this model number” In models that do not support the Trigger
2 output, this error is returned if trying to set Trig 2 Out and a query of Trig 2 Out returns OFF.

Preset

Trigger 1: Sweeping (HSWP)

Trigger 2: Gate

This is unaffected by a Preset but is preset to the above values on a "Restore Input/Output Defaults"
or "Restore System Defaults->All"

State Saved

Saved in instrument state

Initial S/W Revision

Prior to A.02.00

120

Sequence Analyzer User's & Programmer's Reference

«
...
118
119
120
121
122
...
»

Содержание E6650A EXF


















































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды