Keysight E6650A EXF Скачать руководство пользователя страница 156 | Manualshive

Страница: 156 / 657

background image

5 System Functions
System

not put into the SCPI error queue by default. Normally the status bit is the only way for detecting these
errors remotely.

It is possible to enable Input Overload reporting to the SCPI queue, by issuing the
:SYSTem:ERRor:OVERload ON command. To return to the default state, issue the
:SYSTem:ERRor:OVERload OFF command. In either case, Input Overloads always set the status bit.

For versions of firmware before A.10.01, the Input Overload was only a Warning and so was never available
in the SCPI queue, although it did set the status bit. For A.10.01 and later, the Input Overload is an error
and can be enabled to the SCPI queue using this command.

Key Path

SCPI only

Remote Command

:SYSTem:ERRor:OVERload[:STATe] 0|1|OFF|ON

Example

:SYST:ERR:OVER 1 Enable overload errors

Preset

Set to OFF by Restore Misc Defaults (no Overload errors go to SCPI)

State Saved

Saved in instrument state.

Initial S/W Revision

A.10.01

Power Up (Remote Command Only)

This serves to show the errors encountered during the application boot-up, such as: mismatch FW-FPGA,
missing Calibration data, missing hardware and construction errors.

Remote Command

:SYSTem:ERRor:PUP?

Notes

If no error occurs, the return value will be: “No Power Up Errors.”

Return Value: <list of error strings>.

<List of error strings> is an <IEEE488 Block> format.

Return Value Example:

“Power up errors, see details in Windows Event Log”

"Unmatched FPGA Version(s), See details in Windows Event Log”

Initial S/W Revision

E.14.30

System

The System screen is formatted into three groupings: product descriptive information, options tied to the
hardware, and software products:

156

Sequence Analyzer User's & Programmer's Reference

«
...
154
155
156
157
158
...
»

Содержание E6650A EXF


















































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для E6650A EXF

Бренд: Campbell Страницы: 2

Бренд: Danelec Страницы: 67

Бренд: Federal Signal Corporation Страницы: 4

Бренд: ParaBody Страницы: 7

Бренд: Haaga Страницы: 31

Бренд: Ultraflex Страницы: 3

Бренд: Fenton Страницы: 16

Бренд: P.Lindberg Страницы: 76

Бренд: Mangar International Страницы: 8

Бренд: Malvern Instruments Страницы: 30

Бренд: zarges Страницы: 36

Бренд: Rainbow Страницы: 35

Бренд: Rain Harvesting Страницы: 2

Бренд: Vahle Страницы: 36

Бренд: Vahle Страницы: 20

Бренд: Vacon Страницы: 102

Бренд: Hoist Fitness Страницы: 17

Бренд: Peak Pilates Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды