Keysight E6650A EXF Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 657

background image

1 About the Sequence Analyzer Application
What Does the Sequence Analyzer Application Do?

What Does the Sequence Analyzer Application Do?

The Sequence Analyzer mode makes it possible to define, save, and execute a series of data acquisitions
(controlled by the analyzer list sequencer) and/or a series of RF stimulus outputs (controlled by the source
list sequencer). This defined series of acquisitions and/or outputs is known as a sequence.

The test set's source list sequencer and analyzer list sequencer, which are controlled and coordinated by
the Sequence Analyzer mode, allows you to both set up a sequence of data to be output from the test set
and also to set up a sequence of data acquisitions, and define the measurements to be performed on the
data received at the test set input. The sequences are designed for calibration and verification of a mobile
device, and are set up in the test set to correspond exactly with the sequences that are expected at the
mobile device receiver and are generated by the mobile device transmitter, without the need for call
processing.

The flexibility of the list sequencers allows you to set up and make many complex measurements on
defined sets of data, using many different radio standards, all at high speed. It also allows the test set to
be configured to suit the unique requirements of a particular testing situation.

You can run the source list sequencer independently of the analyzer list sequencer (in any mode), but to
run the analyzer and source list sequencers simultaneously, you must be in the Sequence Analyzer mode.

The List Sequencer measurement of the Sequence Analyzer mode actually encompasses several possible
measurements. In addition to the four basic measurements (power, phase & frequency, discrete PAvT, and
IQ data) which are native to the Sequence Analyzer mode, the List Sequencer measurement can make use
of several measurements “borrowed” from other measurement modes. However, in order for the List
Sequencer to use a measurement from another mode, that mode must be licensed on the test set. (For
example, the W-CDMA U9073A application must be licensed on the test set in order for the List Sequencer
to use measurements from the W-CDMA mode.)

36

Sequence Analyzer User's & Programmer's Reference

«
...
34
35
36
37
38
...
»

Содержание E6650A EXF


















































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для E6650A EXF

Бренд: Palazzetti Страницы: 112

WJHD100 - DIGITAL DISC RECORDE

Бренд: Panasonic Страницы: 7

medialon Showmaster Go

Бренд: 7th Sense Страницы: 9

Бренд: Xebex Fitness Страницы: 15

Бренд: qeedo Страницы: 2

Бренд: IDEAL Networks Страницы: 60

Бренд: IceCure Страницы: 104

Бренд: Varytec Страницы: 5

Бренд: Saab Страницы: 98

Бренд: Kaixin Страницы: 89

Бренд: H&S Страницы: 42

Бренд: Vahle Страницы: 36

Бренд: Vahle Страницы: 20

Бренд: Vacon Страницы: 102

Бренд: Valmar Страницы: 78

Бренд: Valhalla Scientific Страницы: 64

Бренд: Mac Medical Страницы: 23

Бренд: Cooper Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды