Keysight E6650A EXF Скачать руководство пользователя страница 550 | Manualshive

Страница: 550 / 657

background image

6 List Sequence Measurements
Source

Select Waveform

Allows you to access to the waveform selection sub-menus.

Pressing this key changes the central view area to show the Waveform File Selection view.

Key Path

Source, Modulation Setup, ARB

Initial S/W Revision

A.05.00

Select Waveform

Allows you to select a waveform sequence or segment for the dual ARB to play.

Key Path

Source, Modulation Setup, ARB, Select Waveform

Remote Command

:SOURce:RADio:ARB:WAVeform <string>

:SOURce:RADio:ARB:WAVeform?

Example

:SOUR:RAD:ARB:WAV “test_waveform.bin”

Notes

If intended waveform is not in the memory yet, then issuing this command by SCPI will invoke ARB
loading operation first, which involves a delay of unpredictable length. So this command should be
followed by the query *OPC?, which holds off subsequent commands until the loading operating is
complete.

<string> - specifies the name of the waveform segment or waveform sequence to be played by the
ARB.

When in Sequence Analyzer mode, and Include Source is Yes, if the you attempt to play a waveform
sequence but not all the required waveform segments are in the ARB playback memory, the
application will reject the loading operation with an error is generated .

When Include Source is No, if you attempt to play a waveform sequence but not all the required
waveform segments are contained in the ARB playback memory, the application will attempt to load
the required segments from either the default directory of the current directory. If the ARB memory
does not have enough space for all the waveform segments to be loaded, an error is generated and
none of the waveform segments is loaded.

If the ARB is ON, and you attampt to play a waveform sequence but not all the waveform segments
within the sequence could be found to be loaded into ARB memory, an error is generated. The
selected waveform keeps the previous value and ARB state remains On.

If you specify a waveform segment over SCPI but the waveform segment is not present within ARB
playback memory and cannot be found for auto loading within the current directory or the default
directory, an error is generatedand the file selection remains unchanged.

If you select a waveform for playback and the waveform requires a license that is not installed on the
instrument, an error is generated.error is generated.

If the ARB is ON and you load a file to ARB memory or delete a file from ARB memory, the playing
waveform segment may not keep phase continuity during the ARB memory operation. The waveform
will be replayed after the ARB operation is finished.

Initial S/W Revision

A.05.00

550

Sequence Analyzer User's & Programmer's Reference

«
...
548
549
550
551
552
...
»

Содержание E6650A EXF


















































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для E6650A EXF

Бренд: Raven Страницы: 27

Бренд: Raven Страницы: 79

Бренд: Raven Страницы: 88

Бренд: Landoll Страницы: 34

Бренд: Bante Instruments Страницы: 6

Бренд: idi Страницы: 20

Бренд: G&G Страницы: 2

Бренд: H&S Страницы: 46

Бренд: 4iQ Страницы: 6

PowerGen 5650 Series

Бренд: Qnergy Страницы: 10

GP1313 Schaukel Premium 2.2

Бренд: gartenpirat Страницы: 4

Бренд: Strapack Страницы: 16

Бренд: Hameg Страницы: 60

MIDORI ULB-50sc

Бренд: Ushio Страницы: 24

Бренд: impact Страницы: 8

Бренд: TOTAL10 Страницы: 16

Blue Bullet 1302-BAS

Бренд: BendPak Страницы: 68

Бренд: Blizzard Lighting Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды