Keysight E6650A EXF Скачать руководство пользователя страница 117 | Manualshive

Страница: 117 / 657

background image

3 Input/Output Functions

Input/Output

to Sense and there is a valid external reference present) this information is used by the analyzer to
determine the internal settings needed to lock to that particular external reference signal.

For the instrument to stay locked, the value entered must be within 5 ppm of the actual external reference
frequency. So it is important to get it close, or you risk an unlock condition.

Note that this value only affects the instrument’s ability to lock. It does not affect any calculations or
measurement results. See "Freq Offset" in the Frequency section for information on how to offset
frequency values.

Key Path

Input/Output, Freq Ref In

Remote Command

[:SENSe]:ROSCillator:EXTernal:FREQuency <freq>

[:SENSe]:ROSCillator:EXTernal:FREQuency?

Example

ROSC:EXT:FREQ 20 MHz sets the external reference frequency to 20 MHz, but does not select the
external reference.

ROSC:SOUR:TYPE EXT selects the external reference.

Dependencies

Still available with Internal or Pulse selected, to allow setup for when External is in use. However, the
setting has no effect if the Internal Reference is in use (Freq Ref In set to Internal, Pulse, or
SENSE:INT or SENSE:PULSE).

Preset

This is unaffected by a Preset but is set to 10 MHz on a "Restore Input/Output Defaults" or "Restore
System Defaults->All"

Default Unit

Hz

Initial S/W Revision

Prior to A.02.00

Modified at S/W Revision

A.14.00

RF Output & Test Set Config

The RF Output & Test Set Config key allows you to set the RF Output Port and multiport adapter unit which
is connected to the instrument by USB for download of calibration data and additional control.

This menu also allows you to set Trigger Config which is used to set the input/output type of the 4 Bi-
directional Trigger ports.

Key Path

Input/Output

Preset

All settings under this key are returned to their default state when

Restore Input/Output Defaults

is

pressed.

State Saved

Saved in State

Initial S/W Revision

A.09.49

RF Output

Specifies the RF Output Port used.

Switching from the RF Output port to one of the RFIO ports changes the transmitter performance of the
instrument.

Sequence Analyzer User's & Programmer's Reference

117

«
...
115
116
117
118
119
...
»

Содержание E6650A EXF


















































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для E6650A EXF

Бренд: Abus Страницы: 2

Бренд: Abus Страницы: 12

Бренд: Abu Garcia Страницы: 6

Бренд: HABYS Страницы: 16

Бренд: Laser Страницы: 2

Бренд: Lars Thrane Страницы: 50

Бренд: Rain-Flo Irrigation Страницы: 16

Бренд: GE Страницы: 176

Бренд: Triton Blue Страницы: 11

Бренд: Numark Страницы: 11

Бренд: Lites Страницы: 8

Бренд: Taylor Страницы: 82

Бренд: Tascam Страницы: 100

Бренд: Flex-A-Seal Страницы: 7

Бренд: Topcon Страницы: 38

Бренд: Delfield Страницы: 24

Bug Zappers BZ-15

Бренд: Black Flag Страницы: 2

Бренд: Backyard Play Systems Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды