Keysight E6650A EXF Скачать руководство пользователя страница 272 | Manualshive

Страница: 272 / 657

background image

6 List Sequence Measurements
List Sequence Measurements

off additional commands on GPIB until the acquisition is complete.

READ Commands:

:READ:<measurement>[n]?

•

Does not preset the measurement to the factory default settings. For example, if you have previously initiated the ACP
measurement and you send READ:ACP? it will initiate a new measurement using the same instrument settings.

•

Initiates the measurement and puts valid data into the output buffer. If a measurement other than the current one is
specified, the instrument will switch to that measurement before it initiates the measurement and returns results.

•

For example, suppose you have previously initiated the ACP measurement, but now you are running the channel
power measurement. Then you send READ:ACP? It will change from channel power back to ACP and, using the
previous ACP settings, will initiate the measurement and return results.

•

Blocks other SCPI communication, waiting until the measurement is complete before returning the results

•

If the optional [n] value is not included, or is set to 1, the scalar measurement results will be returned. If the [n] value
is set to a value other than 1, the selected trace data results will be returned. See each command for details of what
types of scalar results or trace data results are available. The binary data formats should be used when handling large
blocks of data since they are smaller and faster than the ASCII format. (FORMat:DATA)

Initial S/W Revision

Prior to A.02.00

Current Measurement Query (Remote Command Only)

This command returns the name of the measurement that is currently running.

Remote Command

:CONFigure?

Example

CONF?

Initial S/W Revision

Prior to A.02.00

Limit Test Current Results (Remote Command Only)

Queries the status of the current measurement limit testing. It returns a 0 if the measured results pass
when compared with the current limits. It returns a 1 if the measured results fail any limit tests.

Remote Command

:CALCulate:CLIMits:FAIL?

Example

CALC:CLIM:FAIL? queries the current measurement to see if it fails the defined limits.

Returns a 0 or 1: 0 it passes, 1 it fails.

Initial S/W Revision

Prior to A.02.00

Data Query (Remote Command Only)

Returns the designated measurement data for the currently selected measurement and subopcode.

272

Sequence Analyzer User's & Programmer's Reference

«
...
270
271
272
273
274
...
»

Содержание E6650A EXF


















































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для E6650A EXF

Бренд: Falcon Страницы: 52

Бренд: Makita Страницы: 8

Бренд: VECTECH Страницы: 5

Бренд: JB-Lighting Страницы: 40

Бренд: Backyard Play Systems Страницы: 74

Бренд: MAHA Страницы: 21

Бренд: MAGUIRE Страницы: 47

Бренд: Labnet Страницы: 12

Бренд: Lafayette Страницы: 10

Бренд: WARPP Страницы: 28

Бренд: Safco Страницы: 2

Бренд: Xtricity Страницы: 4

Magnetic Rail System Premium

Бренд: Geovent Страницы: 12

DL-FLEXILED100W/B

Бренд: Techni-Lux Страницы: 12

Westeel EasyFlow2 100 Series

Бренд: AGI Страницы: 74

PRO-PORTAL 40010021

Бренд: PROLUMIA Страницы: 32

Бренд: Selecta Страницы: 12

Deltastream ME DPHC 0001

Бренд: Xenios AG Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды