Keysight E6650A EXF Скачать руководство пользователя страница 99 | Manualshive

Страница: 99 / 657

Keysight E6650A EXF Скачать руководство пользователя страница 99

3 Input/Output Functions

Input/Output

Key Path

Input/Output, RF Input

Remote Command

[:SENSe]:CORRection:IMPedance[:INPut][:MAGNitude] 50|75

[:SENSe]:CORRection:IMPedance[:INPut][:MAGNitude]?

Example

CORR:IMP 75 sets the input impedance correction to 75 ohms.

CORR:IMP?

Preset

This is unaffected by a Preset but is set to 50 ohms on a "Restore Input/Output Defaults" or "Restore
System Defaults->All"

Some instruments/options may have 75 ohms available.

State Saved

Saved in instrument state

Readback

50

Ω

or 75

Ω

. Current setting reads back to the RF key.

Initial S/W Revision

Prior to A.02.00

RF Input Port

Specifies the RF input port used. The RF Input Port key only appears on units with multiple inputs, and lets
you switch between the two inputs.

Switching from the RF input port to one of the RFIO ports, on units that have them, changes the receiver
performance of the instrument.

Key Path

Input/Output, RF Input

Remote Command

[:SENSe]:FEED:RF:PORT[:INPut] RFIN | RFIN2 | RFIO1 | RFIO2 | RFIO3 |
RFIO4

[:SENSe]:FEED:RF:PORT[:INPut]?

Example

:FEED:RF:PORT RFIN

Dependencies

This key only appears in models that support multiple inputs. If the SCPI command is sent with
unsupported parameters in any other model, an error is generated, –221.1900, “Settings
conflict;option not installed”

When any input is selected in a measurement that does not support it, the "No result; Meas invalid
with this input" error condition occurs, and the measurement returns invalid data when queried.

Preset

This is unaffected by Mode Preset but is set to RF on a "Restore Input/Output Defaults" or "Restore
System Defaults -> All"

State Saved

Saved in instrument state

Readback

The current RF Input Port selected is read back to this key

Backwards
Compatibility SCPI

INPut<1|2>:TYPE INPUT1 | INPUT2

INPut<1|2>:TYPE?

Included for R&S ESU compatibility. In the MXE, the INPUT1 parameter is aliased to RFIN and the
INPUT2 parameter is aliased to RFIN2

Initial S/W Revision

A.05.01

Modified at S/W Revision

A.14.00

Sequence Analyzer User's & Programmer's Reference

99

«
...
97
98
99
100
101
...
»

Содержание E6650A EXF


















































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды