Keysight E6650A EXF Скачать руководство пользователя страница 592 | Manualshive

Страница: 592 / 657

background image

6 List Sequence Measurements
Source

Key Path

Source, Modulation Setup, ARB, Header Utilities

Remote Command

:SOURce:RADio:ARB:HEADer:SAVE

Example

:SOUR:RAD:ARB:HEAD:SAVE

Notes

Attempting to save the header details via SCPI when no waveform was selected for playback will
generate an error.

Initial S/W Revision

A.05.00

Modified at S/W Revision

A.16.00 (AWGN settings will be saved to header as well )

Query Waveform Unique ID (Remote Command Only)

Each Signal Studio waveform contains a unique waveform ID, which recorded in the header. This command
allows you to query the unique waveform ID from the header. This is a SCPI only command. User can also
check

Error! Reference source not found.

for waveform unique ID display.

Remote Command

:MMEMory:HEADer:ID? “<file name>”

Example

:MMEM:HEAD:ID? “test.wfm” (query the waveform already loaded into the ARB memory)

:MMEM:HEAD:ID? “D: VARB\test.wfm” (query the waveform on the hard disk by absolute path)

:MMEM:HEAD:ID? “NVWFM:test.wfm” (query the waveform on the hard disk by MSUS)

Notes

SCPI query only. The queried waveform file can be in ARB memory, or on hard disk. If want to query
ARB in ARB memory, then give out the file name directly. If want to query ARB on the hard disk, then
absolute file path or MSUS should be given along with the file name. The valid MSUS is “NVWFM”
which is mapped to D: VARB on hard disk.

If the file cannot be found in ARB memory or on hard disk, an error is generated.and value –1 is
returned

Initial S/W Revision

A.09.00

Bus Trigger Command (Remote Command Only)

Used to initiate an immediate trigger event if the trigger source is set to Bus.

Remote Command

:SOURce:RADio:ARB:TRIGger:INITiate

Example

:SOUR:RAD:ARB:TRIG:INIT

Initial S/W Revision

A.05.00

AM

Allows access to the menu for configuring the Amplitude Modulation.

592

Sequence Analyzer User's & Programmer's Reference

«
...
590
591
592
593
594
...
»

Содержание E6650A EXF


















































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для E6650A EXF

Бренд: NARGESA Страницы: 33

Бренд: Major Страницы: 52

Бренд: Nitecore Страницы: 4

Бренд: Yamaha Страницы: 46

AquaPure Ei Series

Бренд: Jandy Страницы: 4

AquaPure Ei Series

Бренд: Jandy Страницы: 8

Jandy Pro Series

Бренд: Jandy Страницы: 16

9NP-B7524 Series

Бренд: Nautilus Страницы: 2

Be strong NS 700X

Бренд: Nautilus Страницы: 34

Бренд: Nautilus Страницы: 21

Бренд: Rainin Instrument Страницы: 16

Бренд: Safavieh Страницы: 2

Бренд: Vendlet Страницы: 2

Бренд: Labnet Страницы: 12

Бренд: Vaisala Страницы: 2

Бренд: MAKSIWA Страницы: 155

Бренд: ProLights Страницы: 28

Бренд: Jenx Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды