IBM CPC700 User Manual Download Page 232 | Manualshive

Page: 232 / 268

background image

9-8

General Purpose Timers

9.3.5 GPT Interrupt Mask (GPTIM) Register

Figure 53. Interrupt Mask Register

The upper half of the register, bits [0:4], correspond to the capture timer interrupt masks and the lower half,
bits [16:20], correspond to the compare timer interrupt masks (see Figure 53).

Bits in this register mask both the setting of the corresponding GPTIS bits and the interrupt output signals
to the CPC700 interrupt controller. If masked, GPTIS bits are not set and interrupt signals are not gener-
ated (even if the GPTIE bits are enabled).

In order for interrupt signals to be sent to the CPC700 interrupt controller, the interrupt mask (GPTIM) bits
must be reset (not masked) and the interrupt enable (GPTIE) bits must be enabled.

0 = Mask Disabled
1 = Mask Enabled (Status and Interrupt signals blocked)

All non-reserved Interrupt Mask Register bits reset to “1” (Mask Enabled).

9.3.6 GPT Interrupt Status (GPTIS) Register

Figure 54. Interrupt Status Register

The upper half of the register, bits [0:4], correspond to the capture timer interrupt status and the lower half,
bits [16:20], correspond to the compare timer interrupt status (see Figure 54).

GPTIS status bits for the capture timers are set when a capture event occurs, the capture timer is enabled
and the corresponding capture mask is disabled.

GPTIS status bits for the compare timers are set when a valid comparison is made and the corresponding
compare mask is disabled.

0

1

2

3

4

5

6

7

8

9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31

MSB

LSB

Capture Timer 0 Interrupt Mask
Capture Timer 1 Interrupt Mask
Capture Timer 2 Interrupt Mask
Capture Timer 3 Interrupt Mask

Capture Timer 4 Intr. Mask

Compare Timer 4 Intr. Mask

Compare Timer 0 Intr. Mask
Compare Timer 1 Intr. Mask
Compare Timer 2 Intr. Mask
Compare Timer 3 Intr. Mask

(Reserved Bits)

(Reserved Bits)

MSB

LSB

Capture Timer 0 Interrupt Status
Capture Timer 1 Interrupt Status
Capture Timer 2 Interrupt Status
Capture Timer 3 Interrupt Status

Capture Timer 4 Intr. Status

Compare Timer 4 Intr. Status

Compare Timer 0 Interrupt Status
Compare Timer 1 Interrupt Status
Compare Timer 2 Interrupt Status
Compare Timer 3 Interrupt Status

0

1

2

3

4

5

6

7

8

9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31

(Reserved Bits)

(Reserved Bits)

«
...
230
231
232
233
234
...
»

Summary of Contents for CPC700













































































































































































































































































Reviews:

No comments

Related manuals for CPC700

Brand: FAAC Pages: 12

Brand: C.Nord Pages: 100

CoreBuilder 9000

Brand: 3Com Pages: 78

ACTIVE DRIVER M/M 1.1

Brand: DAB Pages: 10

Brand: d&b audiotechnik Pages: 3

ACTIVE DRIVER M/M 1.1

Brand: DAB PUMPS Pages: 38

Brand: FAAC Pages: 32

Brand: Jedo Pages: 26

Brand: Hach Pages: 36

Brand: Hach Pages: 72

Brand: IDS Pages: 2

Brand: Lakeshore Pages: 186

Brand: U.S. Divers Pages: 22

Brand: Patron Pages: 36

Brand: Ban Seok Pages: 9

Brand: Mitsubishi Pages: 16

Brand: SOMFY Pages: 4

Pearldex Series

Brand: KaMo Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands