IBM CPC700 User Manual Download Page 182 | Manualshive

Page: 182 / 268

background image

5-50

PCI Interface

The following register values provide this address map shown in Figure 43.:

Register Name

Value

-----------------------------------------------------------------------

PMM 0 Local Address

8000_0000h

PMM 0 Mask/Attribute

F800_0001h

128MB, enabled, read prefetching not allowed

PMM 0 PCI Low Address

8000_0000h

PMM 0 PCI High Address

0000_0000h

PMM 1 Local Address

8800_0000h

PMM 1 mask/Attribute

FC00_0003h

64MB, enabled, prefetching allowed

PMM 1 PCI Low Address

9000_0000h

PMM 1 PCI High Address

0000_0000h

PMM 2 Local Address

0000_0000h

PMM 2 Mask/Attribute

0000_0000h

not enabled

PMM 2 PCI Low Address

0000_0000h

PMM 2 PCI High Address

0000_0000h

PTM 1 Memory Size/Attr

F000_0001h

256MB, enabled

PTM 1 Local Address

0000_0000h

PCI PTM 1 BAR

0000_0008h

PCI Memory space, address decode starts at
PCI address 0000_0000h

PTM 2 Memory Size/Attr

0000_0000h

not enabled

PTM 2 Local Address

0000_0000h

PCI PTM 2 BAR

0000_0000h

5.11.1.3 Other Registers that must be Initialized

•

Error handling is initially disabled (error detection masked). If error handling is to be enabled, than the

Error Enable register must be initialized appropriately.

•

The PCI arbiter defaults are enabled. Arbiter options are programmable via the PCI Arbiter Control reg-

ister. If an external arbiter is used, the internal arbiter must be disabled via power on reset pin strap-
ping resistors.

•

The Bridge Options 1 register contains some options for controlling the PLB bus. Its default values can

be used.

•

The Bridge Options 2 register also contains some options for controlling the PCI bus. Its default values

assume that the PCI is run synchronously to the PLB, and that the CPC700 is the primary host
bridge. If the CPC700 is used differently, the values must be changed accordingly.

5.11.1.4 Target Bridge Initialization

The CPC700 can also respond as a config target; however, it only responds as a config target when its ID-
SEL pin is attached (rather than pulled inactive). This is done when the CPC700 is not the primary (host)
PCI bridge. Following reset, the CPC700 defaults to a state where config accesses (as a target) are retried
until the “Host Config Enable” bit is set in the Bridge Options 2 register. This gives the local CPU time to
initialize the PCI interface register set before the host PCI configuration is allowed to proceed.

«
...
180
181
182
183
184
...
»

Summary of Contents for CPC700













































































































































































































































































Reviews:

No comments

Related manuals for CPC700

Leroy-Somer R180

Brand: Nidec Pages: 20

Brand: Dantherm Pages: 96

Brand: Gardner Denver Pages: 22

Brand: B&G Pages: 2

Brand: Paradox Pages: 32

Brand: Watts Pages: 4

Brand: WaterCop Pages: 4

Brand: Zamel Pages: 23

Brand: Zamel Pages: 2

Brand: Zamel Pages: 2

Brand: Zander Aachen Pages: 44

Extra Free ROB-01/12-24V

Brand: Zamel Pages: 2

Brand: Zamel Pages: 14

Brand: Bender Pages: 28

Brand: Hirschmann Pages: 48

Brand: Nibe Pages: 84

Brand: IBC control Pages: 16

Brand: Securi-Prod Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands