IBM CPC700 User Manual Download Page 211 | Manualshive

Page: 211 / 268

background image

CPC700 User’s Manual—Preliminary

8-5

This register is not used for 7-bit addressing. Ten-bit addressing requires this register to be programmed to
‘1111 0yyX’ binary, where:

yy = The high order two bits of the 10-bit address

X = Don’t care

Thus, in 10-bit address mode, bits 0:6 are used to form the address that is transmitted on the IIC bus and
bit 7 is don’t care.

8.4.3 Control Register

This register must be the last register programmed. Once the pending transfer bit is set, the IIC interface
will attempt to perform the requested transfer using the values in the other registers. Note that not all of the
registers in the IIC interface need to be programmed every time a transfer needs to be performed.

Only the pending transfer bit is cleared to a logic 0 when the requested transfer has been completed. The
remaining bits are left unaffected.

Count bits(0:1) (bits 2:3 of the Control Register) are defined as follows:

0x0

Transfer one byte

0x1

Transfer two bytes

0x2

Transfer three bytes

0x3

Transfer four bytes

During the transfer, and when the transfer is complete, the status and extended status registers can be
read by the program to determine the state of the IIC interface and the IIC bus.

See Table 78 “IIC Registers” on page 8-2.

Table 81. Lo Master Address Register

Register ‘FF6X_0004’ - Lo Master Address

bit 0

Address bit 0 (MSB)

bit 1

Address bit 1

bit 2

Address bit 2

bit 3

Address bit 3

bit 4

Address bit 4

bit 5

Address bit 5

bit 6

Address bit 6 (LSB - 7 bit address)

bit 7

Address bit 7 (LSB - 10 bit address; D.C. for 7 bit)

Table 82. Hi Master Address Register

Register ‘FF6X_0005’ - Hi Master Address

bit 0

Address bit 0 (MSB)

bit 1

Address bit 1

bit 2

Address bit 2

bit 3

Address bit 3

bit 4

Address bit 4

bit 5

Address bit 5

bit 6

Address bit 6

bit 7

Address bit 7 (LSB - D.C. for 10 bit address)

«
...
209
210
211
212
213
...
»

Summary of Contents for CPC700













































































































































































































































































Reviews:

No comments

Related manuals for CPC700

Brand: Nelsen Corporation Pages: 16

Brand: National Instruments Pages: 34

Brand: D-Link Pages: 40

Brand: Sole Diesel Pages: 8

Brand: B&R Industries Pages: 89

Brand: ICP DAS USA Pages: 4

Brand: ICP DAS USA Pages: 6

EIP-2000 Series

Brand: ICP DAS USA Pages: 19

Brand: Madas Pages: 6

Brand: Madas Pages: 11

Brand: R82 Pages: 89

Brand: National Instruments Pages: 8

Brand: Ultratec Pages: 33

Brand: C&C Pages: 17

Brand: TCi Pages: 9

Real Living iM1

Brand: Yale Pages: 2

Brand: HW Group Pages: 18

Brand: DSEGenset Pages: 74

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands