IBM CPC700 User Manual Download Page 60 | Manualshive

Page: 60 / 268

background image

3-24

Processor Interface

• CPC700 will not assert MCP_N while MCP_REQ is active unless MCP_N assertion is enabled. If

MCP_REQ is active when MCP_N assertion is enabled, then MCP_N will be asserted.

• Unlike other processor bus related error sources, when CPC700 samples MCP_REQ asserted, it does

NOT disable further error detection.

3.15.9 ECC Errors

When an uncorrectable ECC error occurs, MCP_ N will be asserted for a minimum of two clock cycles if bit
1 (MCP enable bit) of the PRIFOPT1 register is set.

Correctable ECC errors will be reported to the CPC700’s interrupt controller via IRQ 0. System software
may separately program the interrupt controller to generate an interrupt to the processor based on this
condition or not. See Section Chapter 10., “Interrupt Controller” for more information

3.16 Processor Interface Register Description

Processor interface registers are accessed through the PIFCFGADR and PIFCFGDATA registers. To
access one of the processor interface configuration registers, write the appropriate index to register
PIFCFGADR, then read the data from or write the data to register PIFCFGDATA. All configuration
accesses from the processor must be 4 Byte aligned, otherwise an error will be generated and the cycle
not performed.

Note: In the tables of register field descriptions throughout this specification, some bits are shown shaded.
Those bits are reserved in the CPC700. Reading of reserved bits will produce unpredictable values. Soft-
ware must use appropriate masks to extract the desired bits. Writes must preserve the values of reserved
bit positions by first reading the register, merging the new values, and writing the result back.

Register

Address

R/W

Description

PIFCFGADR

FF50_0000

R/W

Processor Interface Configuration Address Register

PIFCFGDATA

FF50_0004

R/W

Processor Interface Configuration Data Register

«
...
58
59
60
61
62
...
»

Summary of Contents for CPC700













































































































































































































































































Reviews:

No comments

Related manuals for CPC700

Brand: UniKey Pages: 20

SolarCell Remote

Brand: Samsung Pages: 2

Brand: Samsung Pages: 20

Brand: LLURIA Pages: 2

Brand: WAC Pages: 5

TBEN-L 8IOL Series

Brand: turck Pages: 148

APEXpy 07-37A2-2111/ 520Series

Brand: Bartec Pages: 98

Brand: Atari Pages: 3

Brand: Konig Pages: 47

Brand: Estun Pages: 41

Elan SRB 201ZH X3

Brand: schmersal Pages: 6

Brand: Inovance Pages: 2

Chorus GW 10 752

Brand: Gewiss Pages: 64

Brand: Magnetek Pages: 19

Brand: Aruba Networks Pages: 2

Brand: G-Scale Graphics Pages: 7

altecnic 201-2001

Brand: CALEFFI Pages: 8

Brand: Vageo Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands