IBM CPC700 User Manual Download Page 32 | Manualshive

Page: 32 / 268

background image

2-4

Signal Descriptions

REQ0_N/
GNT_N

Low

I

Request[0] / Grant: When the internal PCI arbiter is enabled, this signal
functions as the Request[0] input from another PCI master device.

When the internal PCI arbiter is disabled and an external arbiter is
employed, this signal is the Grant input for the CPC700 from the external
arbiter.

REQ1_N

Low

I

Request[1]: When the internal PCI arbiter is enabled, this signal
functions as the Request[1] input from another PCI master device. If the
PCI internal arbiter is not used, this signal is not used and should be
pulled high.

The internal PCI arbiter provides arbitration for 6 PCI master devices.
Request inputs [2-5] are multiplexed with the processor Data Parity
signals. If processor data parity is enabled, the internal PCI arbiter will
be disabled.

GNT0_N/
REQ_N

Low

O

Grant[0] / Request: When the internal PCI arbiter is enabled, this signal
functions as the Grant[0] output to another PCI master device.

When the internal PCI arbiter is disabled and an external arbiter is
employed, this signal is the Request output for the CPC700 to request
the use of the PCI bus.

The internal PCI arbiter provides arbitration for 6 PCI master devices.
Grant outputs [2-5] are multiplexed with the processor Data Parity
signals. If processor data parity is enabled then the internal PCI arbiter
will be disabled.

GNT1_N

Low

O

Grant[1]: When the internal PCI arbiter is enabled, this signal functions
as the Grant[1] output from the CPC700 to another PCI master device. If
the PCI internal arbiter is not used, this signal is not used.

PCI_66_STRAP High

I

66MHz Operation Strap: This signal is used to indicate to the CPC700
that the PCI bus is operating at higher than 33MHz.

Signal Name

Active
Level

I / O

Description

«
...
30
31
32
33
34
...
»

Summary of Contents for CPC700













































































































































































































































































Reviews:

No comments

Related manuals for CPC700

Brand: Abus Pages: 12

Brand: Daikin Pages: 56

Brand: Danfoss Pages: 36

Brand: Parker Pages: 44

Brand: Nacon Pages: 24

Brand: NAD Pages: 4

Brand: NAD Pages: 4

Brand: MULTISPAN Pages: 2

Brand: Bettis Pages: 18

Brand: EisSound Pages: 10

MURPHYMATIC ASM160

Brand: Murphy Pages: 4

Brand: Pangolin Pages: 35

Brand: Barco Pages: 4

Z8 Encore! XP Dual F1680 Series

Brand: ZiLOG Pages: 18

Brand: Danfoss Pages: 10

Brand: SimCom Pages: 13

Brand: Samlex Solar Pages: 3

Brand: Dataq Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands