Fujitsu F2MC-16LX Series Hardware Manual Download | Manualshive

Page: 507 / 710

background image

489

CHAPTER 16 CAN controller

Table 16.3-3 Functions of Control Status Register (Low) (CSR: L) (1/2)

bit name

Function

bit0

HALT:
Bus halt bit

This bit controls the bus halt.The halt state of the bus can be checked by reading the HALT bit.

At reading
"0":

on bus operation

"1":

halting bus operation

At writing
"0":

cancels bus halt

"1":

set bus halt

Note: When write 0 to this bit during the node status is Bus Off, ensure that 1 is written to this bit.
Reference programming example:

switch (IO_CANCT0.CSR.bit.NS)
{
   case 0:/* error active */
       break;
   case 1:/* warning */
       break;
   case 2:/* error passive */
       break;
   default:/* bus off */
       for (i=0; (i<= 500) || (IO_CANCT0.CSR.bit.HALT= 0):i++);
       IO_CANCT0.CSR.word = 0x0084; /* halt = 0 */
}
*: The valiable i is used for fail safe.

[Conditions for halting bus]

•

Hardware reset

•

Node status transition to bus off

•

Writing "1" to HALT bit

[Operation when bus halted]
Message being transmitted: Bus halted after completion of transmitting
Message being receiving: Bus halted immediately
Storing in message buffer: Bus halted after completion of storing

Note:
•

To check whether the bus is halted, read the value of the HALT bit.

•

Before switching to the low power consumption mode, write "1" to the HALT bit and then read the HALT bit
to check that the bus is completely halted (CSR: HALT = 1).

[Conditions for canceling bus halt]

•

The state in which the bus is halted by a hardware reset or by writing "1" to the HALT bit is cancelled after 0
is written to the HALT bit and an 11-bit High level (receive) is input continuously to the receive input pin
(RX).

•

The state in the bus off is cancelled after "0" is written to the HALT bit and an 11-bit High level (receive) is
input continuously 128 times to the receive input pin (RX).

•

The values of the transmit and receive error counters are both returned to "0" and the node status transits to
error active.

Note: When write 0 to this bit during the node status is Bus Off, ensure that 1 is written to this bit.

[State in which bus halted]

•

Transmitting and receiving are not performed.

•

A High level (receive) is output to the transmit output pin (TX).

•

Other registers or error counters are not updated.

Note:
•

Set the bit timing register (BTR) after halting the bus.

bit1

Reserved:
reserved bit

Be sure to set this bit to "0".

Read: "0" is always read.

«
...
505
506
507
508
509
...
»

Summary of Contents for F2MC-16LX Series







































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for F2MC-16LX Series

ShareCenter DNS-320L

Brand: D-Link Pages: 4

Brand: Aastra Pages: 2

Brand: Udoo Pages: 7

Brand: Rane Pages: 4

Brand: Javad Pages: 35

Brand: Clavister Pages: 89

Brand: CNC4PC Pages: 11

Brand: DigiTech Pages: 6

Brand: Technics Pages: 20

Brand: Xenteq Pages: 16

Brand: Maxtor Pages: 2

Brand: Microtek Pages: 25

Brand: Neousys Technology Pages: 24

Brand: Trend Micro Pages: 2

Brand: XtendLan Pages: 17

GigaVUE H TA100-CXP

Brand: Gigamon Pages: 115

Brand: Valcom Pages: 4

Brand: Advantech Pages: 59

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands