Fujitsu F2MC-16LX Series Hardware Manual Download | Manualshive

Page: 418 / 710

background image

400

CHAPTER 14 UART0

●

Reception Interrupt

When a receive interrupt is enabled (SSR0: RIE = 1), a receive interrupt request is issued at completion of

data receiving (SSR0: RDRF = 1) or when any one of the overrun error (SSR0: ORE = 1), framing error

(SSR0: FRE = 1), and parity error (SSR0: PE = 1) occurs.

When serial input data register 0 (SIDR0) is read, the receive data load flag (SSR0: RDRF) is automatically

cleared to 0.Each reception error flag (SSR0: PE, ORE, FRE) is cleared to "0" when "0" is written to the

reception error flag clear bit (SCR0: REC).

●

Transmission Interrupt

The transmit data write flag bit (SSR0: TDRE) is set to "1" when data to transmit is transferred from serial

output data register 0 (SODR0) to the transmission shift register.

If the transmission interrupt enable bit (SSR0: TIE) contains 1, a transmission interrupt request is

generated.

■

Interrupt Related to UART0 and EI

2

OS

■

EI

2

OS Function of UART0

The UART0 supports EI

2

OS.Consequently, EI

2

OS can be started separately for receive interrupts and

transmit interrupts.

●

At reception:

MB90895 series cannot use interrupt vectors as it contains no I

2

C interface.

●

At transmission:

Since the interrupt control register (ICR14) is shared with the UART0 for reception interrupts, EI

2

OS can

be started only when no interrupt is used for transmission by the UART0.

Note:

If a reception error (parity error, overrun error, or framing error) occurs, correct the error as
necessary, and then write "0" to the reception error flag clear bit (SCR0: REC) to clear each
reception error flag.

Note:

For details of the interrupt number, interrupt control register, and interrupt vector address, see
3.5 Interrupt.

«
...
416
417
418
419
420
...
»

Summary of Contents for F2MC-16LX Series







































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for F2MC-16LX Series

Transportation FiberinMotion

Brand: Radwin Pages: 122

Brand: Delta Tau Pages: 74

Brand: Lanner Pages: 109

PG-FLEX RT FRL-752

Brand: PairGain Pages: 6

Brand: VCS Pages: 118

Brand: ICP DAS USA Pages: 8

Brand: ICP DAS USA Pages: 62

dspstak 21262sx

Brand: Danville Signal Processing Pages: 35

Brand: ZALMAN Pages: 9

Brand: Aaeon Pages: 61

BROADCAST POLLING FRAD BPF-14 BU

Brand: DCB Pages: 28

Brand: Logicube Pages: 56

CG9103-2RS232-1USB

Brand: BiPOM Electronics Pages: 8

Brand: PairGain Pages: 68

Transistor 2SC5378

Brand: Panasonic Pages: 3

Switching Diodes MA6X128 (MA128)

Brand: Panasonic Pages: 3

Brand: Eagle Eye Pages: 61

Brand: F5 Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands