Fujitsu F2MC-16LX Series Hardware Manual Download Page 542 | Manualshive

Page: 542 / 710

background image

524

CHAPTER 16 CAN controller

Table 16.3-20 Functions of Acceptance Mask Select Register (AMSR)

Bit name

Function

bit0

:

ASM7.0 to 0.0, 7.1 to
0.1:

These bits select the mask (acceptance mask) format for
comparison between the received message ID and message
buffer ID (IDR) for the message buffer (x). No comparison with
masked bits is made.
Full-bit comparison: All bits are compared in collating the
setting values of the ID register (IDR) with the received message
ID.
Full-bit masking: All bits for the setting values of the ID register
(IDR) and the received message ID are masked.
Using acceptance mask register 0 (or 1): The acceptance mask
register 0 or 1 (AMR0 or AMR1) is used as an acceptance mask
filter.At collating the setting values of the ID register (IDR) with
the received message ID, only the bits set to 0 and corresponding
to the AMx bit in the acceptance mask register are compared and
the bits set to 1 and corresponding to the AMx bit are masked.
•

If the AMSx.1 and AMSx.0 bits are set to 10 B or 11 B,
always set the acceptance mask register (AMR0 or AMR1)
to be used, too.

Note:
•

The acceptance mask select register (AMSR) should be set
after disabling the message buffer (x) to be set (BVALR:
BVALx = 0). Setting the acceptance mask select register
(AMSR) with the message buffer (x) enabled may store a
message unnecessary received.

:
:
:

Acceptance mask select
bits 7.0 to 0.0, 7.1 to 0.0

bit15

«
...
540
541
542
543
544
...
»

Summary of Contents for F2MC-16LX Series







































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for F2MC-16LX Series

Brand: Genie Pages: 15

Brand: protech Pages: 95

Brand: XtendLan Pages: 228

Brand: Z-Com Pages: 18

Brand: Rainbow Pages: 2

Brand: Intercoax Pages: 2

Brand: Dataprobe Pages: 16

Brand: Konica Minolta Pages: 31

Brand: Quatech Pages: 5

Brand: El.Mo Pages: 16

Brand: Intel Pages: 469

EdgeSafe M40G1AC

Brand: Garland Pages: 159

Brand: UltrArmor Pages: 3

Brand: ubiquoss Pages: 46

VOYIX 7772-K141

Brand: NCR Pages: 10

Brand: PairGain Pages: 68

Brand: Adeunis RF Pages: 9

Brand: protech Pages: 110

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands