Fujitsu F2MC-16LX Series Hardware Manual Download

Page: 154 / 710

136

CHAPTER 3 CPU

3.8.5.1

Sleep Mode

The sleep mode stops the operating clock to the CPU during an operation in each clock
mode.The CPU stops and the resources continue to operate.

■

Transition to Sleep Mode

When the mode transits to the sleep mode by setting the low-power consumption mode control register

(LPMCR: SLP = 1, STP = 0), the mode transits to the sleep mode according to the settings of the MCS and

SCS bits in the clock select register (CKSCR).

Table 3.8-4 shows the settings of the MCS and SCS bits in the clock select register (CKSCR) and the sleep

modes.

●

Data retention function

In the sleep mode, data in the dedicated registers such as accumulators and internal RAM are held.

●

Operation when interrupt request generated

If an interrupt request is generated when the SLP bit in the low-power consumption mode control register

(LPMCR) is set to "1", the mode does not transit to the sleep mode.If the CPU is not ready to accept any

interrupt request, the instruction next to the currently executing instruction is executed.If the CPU is ready

to accept any interrupt request, an interrupt operation immediately branches to the interrupt processing

routine.

●

Pin state

In the sleep mode, pins other than those used for bus input/output or bus control are held in the state before

transiting to the sleep mode.

Table 3.8-4 Clock select register (CKSCR) settings and sleep modes

Clock select register (CKSCR)

Sleep Mode to be transited

MCS

SCS

Main sleep mode

PLL sleep mode

Sub-sleep mode

Notes:

•

If both the STP and SLP bits in the low-power consumption mode control register

(LPMCR) are set to "1" simultaneously, the STP bit is preferred and the mode transits to

the stop mode.When the SLP and TMD bits are set to "1" and "0", respectively, at the

same time, the TMD bit supersedes the SLP bit, causing a transition to the timebase timer

mode or watch mode.

•

There is no sub-clock in MB90F897S.

Summary of Contents for F2MC-16LX Series







































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for F2MC-16LX Series

Reviews:

Related manuals for F2MC-16LX Series

Brands by name

Popular brands

Fujitsu F2MC-16LX Series, Hardware Manual

Search results

Summary of Contents for F2MC-16LX Series

Reviews:

Related manuals for F2MC-16LX Series

Brands by name

Popular brands