Fujitsu F2MC-16LX Series Hardware Manual Download | Manualshive

Page: 114 / 710

background image

96

CHAPTER 3 CPU

3.6

Reset

When a reset trigger even occurs, the CPU immediately suspends the current process
and starts the reset operation. The reset factors are as follows:
• Power on reset
• Watchdog timer overflow
• Generation of software reset request
• Generation of external reset request (RST pin)

■

Reset Factor

●

Power on reset

•

The power on reset occurs at power on.

•

The reset operation is executed after the oscillation stabilization wait time of 2

18

/HCLK has elapsed.

●

Watchdog timer reset

•

Unless the watchdog timer is periodically cleared at the interval time to be repeatedly counted after

starting, an overflow occurs, causing a reset.

•

The oscillation stabilization wait time is not generated by a watchdog timer reset.

●

Software reset

•

The software reset occurs when "0" is written to the internal reset signal generation bit (LPMCR: RST)

in the low-power consumption mode control register.

•

The oscillation stabilization wait time is not generated by a software reset.

●

External reset

•

The external reset occurs when a Low level is input to the external reset pin (RST pin). The time for

Table 3.6-1 Reset Factor

Reset

Factor

Machine

clock

Watchdog timer

Oscillation Stabilization

Waiting

Power on reset

At power on

MCLK

Stops

Yes

Watchdog timer
reset

Watchdog timer overflow

MCLK

Stops

None

Software reset

"0" is written to the RST bit

MCLK

Stops

None

External reset

Input "L" level to RST pin

MCLK

Stops

None

MCLK: Main clock

Note:

For details on the watchdog timer, see CHAPTER 6 WATCHDOG TIMER.

«
...
112
113
114
115
116
...
»

Summary of Contents for F2MC-16LX Series







































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for F2MC-16LX Series

Brand: ebm-papst Pages: 6

Brand: ebm-papst Pages: 6

Brand: ebm-papst Pages: 5

Brand: Paradyne Pages: 45

Brand: Pima Pages: 4

Brand: Compro Technology Pages: 2

Brand: Microchip Technology Pages: 9

Brand: ICP Pages: 68

Brand: Datum Pages: 49

Brand: CAME Pages: 32

Brand: Vista Pages: 93

Brand: Fast Pages: 66

Brand: Yeastar Technology Pages: 2

EISBLOCK AURORA ACRYL GPX-N RTX 3070 VENTUS INCL

Brand: Alphacool Pages: 3

Brand: Hama Pages: 10

Brand: RadiSys Pages: 6

Brand: Linksys Pages: 37

STEVAL-IHT003V1

Brand: ST Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands