Fujitsu F2MC-16LX Series Hardware Manual Download

Page: 486 / 710

468

CHAPTER 15 UART1

11: TDRE = 0) in the serial output data register (SODR1). Also, before and after transmitting, always

return to the mark level (High level).

●

Error detection

Only overrun errors can be detected.Parity and framing errors cannot be detected.

●

Setting of register

shows the setting of the control register in transmitting serial data from the transmitting end to the

receiving end using the clock synchronous mode (operation mode 2).

●

Starting communications

When send data is written to the serial output data register 1 (SODR1), communication starts. When

starting communication only in receiving, it is always necessary to write dummy send data to the serial

output data register 1 (SODR1).

●

Terminating communications

Upon completion of transmission/reception of one frame of data, the receive data load flag bit (bit 12 in the

SSR1 register: RDRF) is set to 1.When data is received, check the overrun error flag bit (SSR1 register bit

14: ORE) to ensure that the communication has performed normally.

Table 15.6-2 Setting of Control Register

bit name

Setting

Transmit End (output serial clock)

Receive End (input serial clock)

Serial mode register 1
(SMR1)

MD1,
MD0

Set clock synchronous mode (MD1, MD0 = "10

CS2, CS1,
CS0

Set clock input source.
• Dedicated baud rate generator (CS2 to

CS0 = "000

to "100

)

• Internal timer (CS2 to CS0 = "110

)

Set clock input source.
• External clock

(CS2 to CS0 = "111

SCKE

Set serial clock output (SCKE = 1).

Set serial clock input (SCKE = 0).

SOE

Set serial data output pin (SOE = 1).

Set general-purpose I/O port (SOE =
0).

Serial control register
1 (SCR1)

PEN

Do not add parity bit (PEN = 0).

8-bit data length (CL = 1)

REC

Initialize error flag (REC = 0).

TXE

Enable transmitting (TXE = 1).

Disable transmitting (TXE = 0).

RXE

Disable receiving (RXE = 0).

Enable receiving (RXE = 1).

Serial status register 1
(SSR1)

TIE

Enable transmitting (TIE = 1)

Disable transmitting (TIE = 0)

RIE

Disable receiving (RIE = 0).

Enable receiving (RIE = 1).

Summary of Contents for F2MC-16LX Series







































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for F2MC-16LX Series

Reviews:

Related manuals for F2MC-16LX Series

Brands by name

Popular brands

Fujitsu F2MC-16LX Series, Hardware Manual

Search results

Summary of Contents for F2MC-16LX Series

Reviews:

Related manuals for F2MC-16LX Series

Brands by name

Popular brands