Fujitsu F2MC-16LX Series Hardware Manual Download | Manualshive

Page: 375 / 710

background image

357

CHAPTER 13 8/10-bit A/D converter

Table 13.3-2 Function of Each Bit of A/D Control Status Register (High) (ADCS: H) (1/2)

bit name

Function

bit8

Reserved: reserved bit

Always set this bit to "0".

bit9

STRT:
A/D conversion software
start bit

This bits starts the 8-/10-bit A/D converter by software.

When set to "1": Starts 8-/10-bit A/D converter

•

If A/D conversion pauses in the pause-conversion mode, it is
resumed by writing "1" to the STRT bit.

When set to "0": Disabled.

The state remains unchanged.

Read: The bit returns "1" when byte/word instructions.
The bit returns "0" when read-modify-write instructions.
Note:

Do not perform forcible termination (BUSY = 0) and software
start (STRT = 1) of the 8-/10-bit A/D converter simultaneously.

bit10
bit11

STS1, STS0:
A/D conversion start
trigger select bits

These bits select the trigger to start the 8-/10-bit A/D converter.
If two or more start triggers are set (except STS1, STS0="00

B

"), the

8-/10-bit A/D converter is started by the first-generated start trigger.
Note:

Start trigger setting should be changed when the operation of
resource generating a start trigger is stopped.

bit12

PAUS:
Pause flag bit

This bit indicates the A/D conversion operating state when the

EI

2

OS function is used.

•

The PAUS bit is enabled only when the EI

2

OS function is used.

•

A/D conversion pauses while the A/D conversion results are
transferred from the A/D data register (ADCR) to
memory.When A/D conversion pauses, the PAUS bit is set to
"1".

•

After transfer of the A/D conversion results to memory, the 8-/
10-bit A/D converter automatically resumes A/D
conversion.When A/D conversion is started, the PAUS bit is
cleared to "0".

bit13

INTE:
Interrupt request flag bit

This bit enables or disables output of an interrupt request.
•

When the interrupt request flag bit is set with an interrupt
request enabled (INTE = 1), an interrupt request is generated.

Note:

Always set this bit to 1 when the EI

2

OS function is used.

bit14

INT:
Interrupt request flag bit

This bit indicates that an interrupt request is generated.
•

When A/D conversion is terminated and its results are stored in
the A/D data register (ADCR), the INT bit is set to "1".

•

When the interrupt request flag bit is set (INT = 1) with an
interrupt request enabled (INTE = 1), an interrupt request is
generated.

When set to "0": The bit is cleared.
When the bit is set to "1": No effect.

When EI

2

OS function started: Cleared

Note:

To clear the INT bit, write "0" when the 8-/10-bit A/D converter
is stopped.

«
...
373
374
375
376
377
...
»

Summary of Contents for F2MC-16LX Series







































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for F2MC-16LX Series

Brand: Omnia Pages: 6

Brand: Xinje Pages: 76

Z3-DM8168-PCI-RPS

Brand: Z3 Technology Pages: 20

Z3-DM8107-SDI2-RPS

Brand: Z3 Technology Pages: 75

Brand: Z-Wave Pages: 13

Brand: Omega Engineering Pages: 34

Brand: Longshine Pages: 27

Brand: 3Ware Pages: 4

Brand: red lion Pages: 5

NIC-FC730i-Mb-2-32G

Brand: H3C Pages: 37

CNPS7000A Series

Brand: ZALMAN Pages: 9

Brand: AMX Pages: 1

zoomno MSC-5578

Brand: BIIZZY Pages: 2

Brand: Intel Pages: 578

Brand: ASROCK Pages: 173

Brand: Rosewill Pages: 2

VAR-SOM-MX8M-PLUS

Brand: Variscite Pages: 2

Brand: ETAS Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands