Fujitsu F2MC-16LX Series Hardware Manual Download | Manualshive

Page: 322 / 710

background image

304

CHAPTER 10 8/16-bit PPG timer

Table 10.3-3 Functions of PPG1 Operation Mode Control Register (PPGC1)

bit name

Function

bit8

Reserved: reserved bit

Always set this bit to "1".

bit9

bit10

MD1, MD0:
Operation mode select
bits

These bits set the operation mode of the 8-/16-bit PPG timer.

(Any mode other than 8-bit PPG output 2-channel
independent operation mode)

• Use a word instruction to set the PPG operation enable bits

(PEN0 and PEN1) at one time.

• Do not set operation of only one of the two channels (PEN1 =

0/PEN0 = 1 or PEN1 = 1/PEN0 = 0).

Note:

Do not set the MD1 and MD0 bits to "10

B

".

bit11

PUF1:
Underflow generation
flag bit

8-bit PPG output 2-channel independent operation mode,
8+8-bit PPG output operation mode: When the value of the
PPG1 down counter is decremented from "00

H

" to "FF

H

",

an underflow occurs (PUF1 = 1).
16-bit PPG output operation mode: When the values of the
PPG0 and PPG1 down counters are decremented from
"0000

H

" to "FFFF

H

", an underflow occurs (PUF1 = 1).

• When an underflow occurs (PUF1 = 1) with an underflow

interrupt enabled (PIE1 = 1), an interrupt request is generated.

When set to "0": The bit is cleared.
When the bit is set to "1": No effect.
Read by read modify write instructions: "1" read

bit12

PIE1:
Underflow interrupt
enable bit

This bit enables or disables an interrupt.

When set to 0: No interrupt request is generated even at
underflow (PUF1 = 1)
When set to 1: Interrupt request is generated at underflow
(PUF1 = 1)

bit13

PE1:
PPG1 Pin output enable
bit

This bit switches the PPG1 pin function to enable or disable the
pulse output.

When set to 0: Functions as general-purpose I/O port

The pulse output is disabled.

When set to 1: PPG0 pin functions as PPG0 output pin.

The

pulse output is enabled.

bit14

Unused bits

Read: The value is undefined.
Write: No effect

bit15

PEN1:
PPG1 operation enable
bit

This bit enables or disables the count operation of the 8-/16-bit
PPG timer 1.

When set to 0: Count operation disabled
When set to 1: Count operation enabled

• When the count operation is disabled (PEN1 = 0), the output

is held at a Low level.

«
...
320
321
322
323
324
...
»

Summary of Contents for F2MC-16LX Series







































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for F2MC-16LX Series

Brand: XDS Pages: 99

Brand: Blackrock Microsystems Pages: 27

Brand: Rolls Pages: 2

Brand: Lutron Electronics Pages: 4

Brand: Aaeon Pages: 61

Brand: JAKA Pages: 37

H8S/2646 Series

Brand: Renesas Pages: 20

Brand: IEI Technology Pages: 136

Brand: Fast Pages: 66

Brand: LevelOne Pages: 142

mPCIE-ADIO16-8F Series

Brand: Acces I/O products Pages: 13

Brand: M86 Security Pages: 540

Brand: Arctic Pages: 7

NexXxoS GPX-N 970 M03

Brand: Alphacool Pages: 2

Brand: Adaptec Pages: 3

Brand: NovaStar Pages: 16

Brand: Acnodes Pages: 10

Brand: ADTRAN Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands