manualshive.com logo in svg

Fujitsu F2MC-16LX Series, Hardware Manual, Page: 456 / 710

Share
Download
Fujitsu F2MC-16LX Series Hardware Manual Download Page 456

438

CHAPTER 15  UART1

Table 15.3-2  Functions of Serial Control Register 1 (SCR1)

bit name

Function

bit8

TXE: 
Transmit enable bit

Enable or disable the UART1 for sending.

When set to "0": Transmission disabled
When set to "1": Transmission enabled

Note:

When transmitting is disabled during transmitting, transmitting stops 
after the data in the serial input data register being transmitted is 
completed in the serial input data register.-
To set this bit to "0", after writing data to SODR1, wait for a time of 1/
16th of the baud rate in the asynchronous mode and for a time equal to 
or more than the baud rate in the synchronous mode.

bit9

RXE:
Receive enable bit

Enable or disable the UART1 for receiving.

When set to "0": Reception disabled
When set to "1": Reception enabled

Note:

When receiving is "disabled" during receiving, receiving stops after the 
data being received is stored in the serial input data register.

bit10

REC:
Receive error flag 
clear bit

Clear the receive error flags (bit 15 to 13: PE, ORE and FRE) of the serial 
status register (SSR1) to "0".

When set to "0": Clears PE, ORE and FRE flags
When set to "1": No effect
When read: 1 always read

Note:

When a receive interrupt is "enabled" (bit 9: RIE = 1), set the bit10: 
REC bit to "0" only when any one of the PE, ORE and FRE flags is set 
to "1".

bit11

A/D: 
Address/data select 
bit

In operation mode 1 (asynchronous multiprocessor mode), set the data 
format of the frame to be transmitted/received.

When bit set to "0": Data frame set
When bit set to "1": Address data frame set

bit12

CL: 
Data-length select bit

Specify the length of send and receive data.
Note:

A data length of "7 bits" can be selected only in operation mode 0 
(asynchronous normal mode).In operation modes 1 and 2 
(asynchronous multiprocessor mode, Clock synchronous mode), be 
sure to set a data length of "8 bits".

bit13

SBL:
Stop-bit length select 
bit

Set the length of the stop bit (frame end mark of send data) in operation 
modes 0 and 1 (multiprocessor mode, synchronous mode).
Note:

At receiving, only the first bit of the stop bit is always detected.

bit14

P:
Parity select bit

Select either odd or even parity when "with parity" (PEN = 1) is set.

bit15

PEN: 
Parity addition 
enable bit

Specify whether to add (at sending) and detect (at receiving) a parity bit.
Note:

A parity bit is not added in operation modes 1 and 2 (Multiprocessor 
mode, Synchronous mode).Be sure to set this bit to "0".

Summary of Contents for F2MC-16LX Series







































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments