Fujitsu F2MC-16LX Series Hardware Manual Download | Manualshive

Page: 49 / 710

background image

31

CHAPTER 3 CPU

3.2

Dedicated Registers

The CPU has the following dedicated registers.
• Accumulator
• User stack pointer
• System stack pointer
• Processor status
• Program counter
• Direct page register
• Bank registers (program bank register, data bank register, user stack bank register,

system stack bank register, additional data bank register)

■

Configuration of Dedicated Registers

Figure 3.2-1 Configuration of Dedicated Registers

AH

AL

USP

SSP

PS

PC

DPR

PCB

DTB

USB

SSB

ADB

: Accumulator (A)

They are two 16-bit registers for calculation.
Consecutively used the registers can be used as 32-bit register.

: User stack pointer (USP)

It is a 16-bit pointer for user stack address.

: System stack pointer (SSP)

It is a 16-bit pointer for system stack address.

: Processor status (PS)

It is a 16-bit register for system status.

: Program counter (PC)

It is a 16-bit register for stored position of current instruction.

: Program bank register (PCB)

It is a 8-bit register for program space.

: Data bank register (DTB)

It is a 8-bit register for data space.

: User stack bank register (USB)

It is a 8-bit register for user stack bank space.

: System stack bank register (SSB)

It is a 8-bit register for system stack bank space.

: Additional data bank register (ADB)

It is a 8-bit register for additional space.

: Direct page register (DPR)

It sets bit 8 to bit 15 in address 24-bit, when executing the instruction
by abbreviated direct addressing. It is a 8-bit register.

8 bits

16 bits

32 bits

«
...
47
48
49
50
51
...
»

Summary of Contents for F2MC-16LX Series







































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for F2MC-16LX Series

Brand: Baicells Pages: 8

Brand: Dahua Pages: 24

INTERNET PRIVACY PROTECTION

Brand: AlphaShield Pages: 49

Brand: hilscher Pages: 154

Brand: XNET Pages: 17

Brand: Waves Pages: 41

Brand: VCS Pages: 118

iTRON B 70.2040

Brand: JUMO Pages: 41

Brand: Cameo Pages: 23

Brand: Medel Pages: 28

Brand: Rane Pages: 128

Brand: Acard Pages: 34

Brand: Shure Pages: 113

J-Link-OB-STM32F072-128KB

Brand: Segger Pages: 18

CHEETAH ST34501FC

Brand: Seagate Pages: 68

Brand: Watchguard Pages: 21

Brand: Kontron Pages: 32

Brand: Xtreme Pages: 83

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands